JES735WJ01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Maria from BRONX, NY
- Parts Used:
- WB49X10134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Tray broke
Great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from DENVER, CO
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Microwave not turning on. All other functions operate
DISCONNECT THE POWER CORD and discharge the capacitor
Leave unplugged overnight
Remove vent grille by removing the 2 philips screws
Remove the LED panel by removing 1 phillips screw
Disconnect all connectors that plug into back of the LED board completely
Remove the wires from the switches (3) at the inside edge of the microwave door
Gently remove each switch housing and test all three switches for continuity
Carefully replace non-functioning switches and reassemble the panel
GOOD LUCK
Leave unplugged overnight
Remove vent grille by removing the 2 philips screws
Remove the LED panel by removing 1 phillips screw
Disconnect all connectors that plug into back of the LED board completely
Remove the wires from the switches (3) at the inside edge of the microwave door
Gently remove each switch housing and test all three switches for continuity
Carefully replace non-functioning switches and reassemble the panel
GOOD LUCK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Bethany Beach, DE
- Parts Used:
- WB49X10134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bought nearly new microwave in thrift store for eight dollars, but it was missing the glass turntable
When I got home that night, I went to your website, ordered the glass turntable, which was the exact replacement part I needed. The shipping was so fast that in two days I had an almost new microwave which cost me a grand total of 31.00. Not too bad! (I priced the same model in other stores and they averaged anywhere from 69.00 to 129.00. Thirty one dollars was way better, don't you agree? I would suggest your site for anyone needing replacement parts. Thanks for your help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from LIVERPOOL, NY
- Parts Used:
- WB49X10134, WB06X10577
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
WORN FLAT SPOTS ON ROLLERS PREVENTING ROTATION OF TRAY
REMOVE OLD PARTS REPLACE WITH NEW
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gilbert from TOMS RIVER, NJ
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Switch went bad, Internal Fan would run every time you open the door
Unscrewed the control panel (2 screws), lift up and let hang, with a plan screwdriver open bracket holding the switch, unplug 2 wires, replace with new switch, plug in the 2 wires, push switch back into bracket. Then slide on the control panel, put the 2 screws back. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from POWELL, OH
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Microwave would not heat up
Part just snapped into place and wires were reattached.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ira from LIVINGSTON, LA
- Parts Used:
- WB27X35382
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Food wouldn't heat up
Googled problem, removed diode, checked with meter and it was open, ordered new diode, checked new diode and it read open, installed. Any way, it didn't work. Went and bought new microwave!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from FULSHEAR, TX
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
M/W would not start. control panel OK
unplugged power
removed main black cover.
located part WB24X10047 and replaced
removed main black cover.
located part WB24X10047 and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- johnny from port orange, FL
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
no power in microwave in turn table wouldn't turn light would work act like door was open
remov cover to check voltage and found problem at the interlock switch ohm the switch and found it was open replace both switches it work fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darin from SAN DIEGO, CA
- Parts Used:
- WB27X35382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No heat. No unusual noise. Appers to function other than no heat
Multimeter checked/confirmed switches, sensors, and fuse first. All good. High power diode was bad - Replaced. Still no heat but now loud "MMMMM" noise when running. This means either the capacitor is also bad and/or magnetron.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Wesley Chapel, FL
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable Stopped Working/Display Timer Would Countdown But Not Heat
With this model, you must remove the outer covering. Don't try to access the display unit from the front like I've seen in some other GE microwave videos. After removing the outer covering, the switches are easy to replace. They are very visible and easy to get to without taking any other parts off. You will see the door switches just behind the display board. Remove the switch and then remove the connecting wires to ensure you don't inadvertently brake a wire. You will need a tamper resistant star bit to remove 3 or 4 screws from the back panel. All other screws are philips head. I went ahead and replaced both switches (yes...there are two of them) and works like a charm. I saved an $800 microwave for less than $60 and know what to do if it happens again. Appears to be a common problem on this model. Thanks for others making a post...It saved me time and money reading others remarks. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CORAL SPRINGS, FL
- Parts Used:
- WB06X10577
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
turntable won't rotate
order replacement part roller guide, Synchronous Motor # GM-16-2F302 unplug appliance,remove glass plate & roller guide. flip over to see screws at bottom & Sides, if you don't have special bit to remove 4 tamper proof screws located on the 4 corners, use Dremel to cut slot on screw head so you can remove screws with flat tip screw driver. Be mindful of the magnetron screwed to bottom plate, Be mindful the bottom plate is sharp, Danger to avoid high voltage capacitor, once screws are removed ease the bottom tray out< Note location of tabs on tray, and alignment slots, you are removing bottom tray to get to turntable motor held on by one screw & tab, note location of black & white wire, swap out motor,carefully re align bottom plate tabs & slots & screw holes re install screws, flip over install roller guide & glass plate, The new roller guide has a pin sticking up from the center, the weight of the glass plate keeps the roller guide engaged on the motor, test, every thing works fine cost of parts under $30 removal & replacement under 1/2 hour,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from BLUFFTON, SC
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
The unit would run when the door was open!
First I had to accept the fact that the unit was designed to keep non-professional people from doing any repairs. The switch was installed in such a manner that I had to break the mounting to remove the switch, then drill a hole in the mounting to secure the new switch in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Reisterstown, MD
- Parts Used:
- WB06X10577
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I Apprently Ordered The Wrong Part,
Just replaced the part. Thank you . . However it was the wrong one. I needed the outside ring. As the one with the wheels is rusting out the bottom of the microwave// would appricate it if you could advise. .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Brooklyn Park, MN
- Parts Used:
- WB06X10577
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Roller Guide for Microwave
Lifted the glass plate and put the roller guide in bottom of microwave on peg.
Was this instruction helpful to you?
Thank you for voting!