JVM1651CB003 General Electric Microwave - Instructions

Removed old film, installed new horizontally and pulled it downward (match it along the top first). The cover required 2 "hooks" to be removed, only needed 4 clips. Used a screwdriver to remove the 2 clips.

Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.

Nice. Half dozen screws drops the bottom, 2 screws on the motor, pop in the new, reassemble and throw in the popcorn. (Was skeptical. Have replaced quite a few of these little motors in data centers. Common part in high-speed printers. Never saw one fail like this but your feedback convinced me otherwise.)

took off steel plate---removed two screws--unpluged drive motor--replaced with new drive motor. reversed removal procedure . Took about 10 minutes.
Great service from PARTSELECT.

Very easy repair I did not even have to take the microwave down. Just removed the 7 screws, the bottom swung down removed the 2 screws holding the motor, unplugged it put the new one in put the screws back and Done.

took 6 screws out of the oven bottom
removed 2 screws that held the motor
diconnected the power plug.

plugged in power to new motor, replaced 2 screws that held it in place, replaced 6 screws that held bottom of oven

That was it...

First I unplugged the microwave from the wall receptacle. Next I removed eight screws that let the bottom plate of the microwave hood pivot down with its hinges. Next I removed two screws holding the turn motor in place. I then unplugged the motor and replaced it with the new motor and reversed the above procedures until everything was back in place. I then turned the microwave on and was thrilled to find it working properly again.

unplugged the appliance, removed the glass tray from inside, turned the microwave on its side and removed the 3x3 panel, removed the drive motor by taking out two screws and disconnecting the two electrical wires, compared the new item with the old one, placed new in olds position and screwed in place. replaced the 3x3 cover, turned microwave upright, plugged in the power cord, placed a cup of water on the tray, turned the microwave on for 30 sec. and watched the table turn. Very simple and convenient application.

took screws out of bottom of microwave.dropped down bottom cover to get at drive motor I took out one screw droped down cooking tray motor disconnnected 2 wires reconnected put back up and put 1 screw in ,fastened bottom and was fixed very easy ,and parts select is the best place to find what you are looking for if I ever need parts this is where I will order from service is great and only took about 2 days to receive my part .I went to store where I bought my microwave and they wanted to sell me a new one.saved over $200

I read several customer reviews before starting the repair. Removed the old drive motor to make sure I was ordering the correct part. Removal consisted of removing the screws on the bottom plate, disconnecting the electrical plug from the motor, and removing the one screw that attached the motor to the housing. Installation of the new motor was the reverse.

I removed the five screws that held the bottom plate in place. After removing the bottom plate, I unscrewed the one screw holding the drive motor, unplugged the motor, and then installed the new motor. Replaced the botton plate and then tested the new motor. Everything worked like new.

The part was less expensive than buying it from GE. I ordered the motor on a Monday morning and received it Wednesday afternoon. I was completely satisified with the price, part, and shipping time.

Thanks,

Removed six screws that allowed the "bottom" to swing down; then removed the two screws holding the motor - disconnected the two wires. Installed the motor and reversed this procedure to finish the project.

Removed the 5 screws that held the housing so it dropped down. removed the 2 screws to the motor. Disconnedted the plug. reinstalled the new motor. connected the plug and raised the housing and replaced the 5 screws. Took less than 10 minutes start to finish. Piece-of-cake.

As in other postings, remove six screws on the bottom of the microwave, disconnected the the plug,unscrew two screws to remove the old motor...(it took longer to get the new part out its box then it did to make the repair) unpacked the new part, put in the two motor screws, put in the six screws to hold the microwave bottom in place and waalaa...done!
Thanks,
Hank

about 6 philips head screws along the bottom drops that cover off. 2 more hold the motor in place.

carefully remove the 2 wire plug onto the motor . do not touch or get near the black wire.unless you want to get shocked.like i did.

remove the 2 motor screws.put the new one up and turn untill the screw holes are the holes in the
lower inner cover. reinstall the screws .reinstall the plug and lower plate.

having been a auto mechanic till i retired, helped me a lot.total time to make the repair was about 15 min.

this is not my first order from parts select and all i can say is they rock with the best of service i have ever gotten for appliance parts. and prices one can not found to beat for factory parts.