JVM1861CD002 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cody from Omaha, NE
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn table stoped functioning
Troubleshooting process:
Using a screw driver I opened the bottom of the unit using a Philips screwdriver and unhooked the drive motor electrical connector. Using a multimeter I checked to ensure power to the motor. This confirmed that the motor is bad and must be replaced.
Repair process:
After receiving new motor I removed the old motor and installed the new one using a Philips screwdriver and closed up the bottom cover.
It functioned good as new. Relatively cheap and very easy fix.
Using a screw driver I opened the bottom of the unit using a Philips screwdriver and unhooked the drive motor electrical connector. Using a multimeter I checked to ensure power to the motor. This confirmed that the motor is bad and must be replaced.
Repair process:
After receiving new motor I removed the old motor and installed the new one using a Philips screwdriver and closed up the bottom cover.
It functioned good as new. Relatively cheap and very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Muskego, WI
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cooking tray drive motor did not work.
Unpugged microwave. Removed the screws on the bottom cover of the micorwave. Unpugged drive motor and removed two screws from drive motor. Installed new motor and replaced the bottom cover, plugged in microwave . . . presto!
Installation was just as easy as numerous other customers indicated. Also, your service was as great as many other customers indicted . . . part was recieved in 2 business days. Thank you for great service and website.
Installation was just as easy as numerous other customers indicated. Also, your service was as great as many other customers indicted . . . part was recieved in 2 business days. Thank you for great service and website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from The Villages, FL
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broke the cooking tray while cleaning it.
Ordered through parts.select because GEprice was totally outrageous.
Unfortunately, my first order was lost and after 2 weeks I phoned your customer service and Betty was quite helpful. She followed up (as I called on a Saturday am) on Monday and reported to me that the item was lost. She then asked me if I wished to place another order. I did, of course - it arrived in a timely manner - I placed the cooking tray into the microwave and I was in business!!! Thank You Partselect!!!!!
Unfortunately, my first order was lost and after 2 weeks I phoned your customer service and Betty was quite helpful. She followed up (as I called on a Saturday am) on Monday and reported to me that the item was lost. She then asked me if I wished to place another order. I did, of course - it arrived in a timely manner - I placed the cooking tray into the microwave and I was in business!!! Thank You Partselect!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Port Saint Lucie, FL
- Parts Used:
- WB02X10733
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
no carbon filter in vent and fan
Had to pry the front top of mircowave open and bend down and force this carbon filter in on an angle .Had to call several numbers for instructions. Very awkward and ridiculous to put carbon filter in-besides, it should have come with one to start with!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Serio from Lansdale, PA
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken glass microwave turn table
The new turntable shipment was super fast!!! I received it only a few days after ordering it. Installation was nothing more than placing it in the microwave oven.
GREAT Transaction!!! Thanjs!!!
GREAT Transaction!!! Thanjs!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan from Torrance, CA
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken tray
Open the box that the part came in and place it in the microwave. The best is how fast it came to my home. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from longbeach, CA
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broke glass turntable
just set the glass turntable in and bingo it worked
no tools needed. thanks for such a fast delivery
sincerly dennis and chris delbello
no tools needed. thanks for such a fast delivery
sincerly dennis and chris delbello
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from Sacramento, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Glass turntable drive motor failure
Removed bottom cover of microwave, involved removing 7 screws, removed turntable motor, involved disconnecting wire harness plug, and 2 screws, connnected wiring to new motor and reinstalled with original hardware
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACK from ETOWAH, NC
- Parts Used:
- WB06X10144
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable quit turning.
Disconnected power cord from receptacle. Removed 5 screws in bottom panel and allowed it to swing downward on rear hinged edge. Disconnnected power wires to motor. Removed screw to detach motor. Inserted coupler through hole beneath center of turntable. Inserted motor shaft into coupler and re-attached motor. Connected power wires to motor and then closed the bottom panel and re-inserted the 5 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Collegeville, PA
- Parts Used:
- WB06X10286
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The glass plate in the microwave stopped turning
After examination - evidently some one had put a larger dish in the microwave and it stopped the glass plate from turning and broke the holder stirrer(small plastic piece that held the glass plate so that it could turn.
When I received the right part I simply made sure that all the prior plastic was out or out of the way and placed the new part onto to the shaft - tested it a few times, made a minor alignment and it has worked fine ever since.
Thanks to your staff for finding the right piece from the description I gave.
When I received the right part I simply made sure that all the prior plastic was out or out of the way and placed the new part onto to the shaft - tested it a few times, made a minor alignment and it has worked fine ever since.
Thanks to your staff for finding the right piece from the description I gave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Mableton, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
noise eminating from carousel
I removed 4 screw from the under carriage of the microwave then, removed the 2 screws from the motor, replaced the motor and replaced the screws. It was so easy it took only 4 minutes to perform, better than replacing the whole unit (microwave) and less expensive too. i only wish it was made in the US, I wouldn't mind to spend a little more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Richland, WA
- Parts Used:
- WB26X10038, WB06X10144
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable wouldn’t turn
I removed a few (6) screws and disengaged the motor. Removed the parts and installed in reverse order. Replaced the screws. Easy
Cleaning up the grease from cooking for years on the stovetop below took WAY longer. But the repair was simple!!
Cleaning up the grease from cooking for years on the stovetop below took WAY longer. But the repair was simple!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marielen from newport, RI
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked Microwave Glass Plate
Odered replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kambiz from Mesa, AZ
- Parts Used:
- WB02X10733
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Charcoil Filter needed to be changed.
GE microwave displayed the message that Charcoil Filter needs to be changed. I disconnected the unit and removed the top two screws then removed the top panel by sliding it gently to the left. Replaced the filter. And positioned it in the same way the old filter was installed. Replaced the top panel and screws, Connected the unit back and used the Menu option to reset the Charcoil Filter warning option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Friendship, MD
- Parts Used:
- WB02X10733
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Needed to change filter
Remove two screws on the top of the grill. Slide the grill to the left and then pull straight off. Slide the filter in place. Replace grill and screws
Was this instruction helpful to you?
Thank you for voting!