ZSC2200NWW02 General Electric Microwave - Instructions

PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.

My daughter hand installed bulbs without a problem, took a minute and used a phillips to reinstall the cover. I shopped on-line because I wasted two hours between Lowe's and Home Depot trying to get the right bulb. I did think your postage was crazy high, otherwise glad to get the right bulbs to solve the problem.

I could not for the life of me figure out how to get into the light housing so I could replace the bulb, nor did I have any idea which bulb to buy. The manual for this model descibes how to replace the underside lighting but they seem to have left out instructions about the interior. I watched the short "how-to" video on this site, bought the bulb that was described and replaced the bulb in five minutes without any issues.

I myself had difficulties replacing bulbs, as I have no feelings in my fingers, so I asked my son while holding the bulb in the bubble wrap, He had no problems what so ever.

Removal of the bulbs was easy; reinserting was not as easy due to the configuration/placement of the bulbs in the unit. It was interesting that a simple suggestion to keep the bulbs covered with some of the packing material made sense as to not directly handling the bulb itself and causing any contamination of the bulb(s).

Removed tiny screw from under the microwave that held the lid shut where the light was located. Took out old bulb and replaced with new one. Very easy!!!!

it work ok now

We followed the instructions on your website and it was very quick and easy. Thank you so much for having that information and showing exactly how to replace the Halogen Light Bulb.

took of the cover, replaced bulbs then replaced bulbs. One was more difficult to get in than the other but all is ok now. No more stove stop cooking in the dark:)

Disassembled the bottom of the microwave in order to access the lightbulb sockets. Unfortunately, 1 of the 2 replacement bulbs broke during the installation process - 1 of the pins broke off while trying to insert it. Now I have only 1 bulb so the light is not as bright as it should be. It took me several trips the HomeDepot only to have to return the bulbs. Fortunately, PartSelect shipped the correct replacement bulbs the first time.

Removed microwave cover using screwdriver and anti tamper bit available at local hardware store. Megnetron had broken magnet making discovery of deffective part easy. Removed wire connector and three screws attaching magnetron to case, removed magnetron and installed new item in reverse order. Installed cover and made popcorn for operational check of microwave. Happy days..........

Used new rubber gloves so as to not get finger prints on the bulbs. Hope that was ok. Trying to use a paper towel was a nuisance. Also had to use a mirror to see the slots for the bulbs. This was actually a pain to do especially since I am short and was on my toes to do this. Only the bright light works and before there was a night light and a bright light. So there you have it.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.

Unplug the microwave. Remove front grill and cover by removing 2 screws on top of microwave. You have to look down from the top. I could not locate the screws by feel. Once the two screws are out, remove the grill by sliding slightly to the left to lift out. Open the oven door to facilitate removal. Then remove the steel light cover (1 Phillips screw in the center of the unit) and unclip the bulb holder on the right. Do not touch the halogen bulb when you replace. Reseat the bulb holder and test by plugging in the unit with the door open. Unplug and replace the light cover and grill.