PSB2201NSS02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- lyle from crosby, TX
- Parts Used:
- WB44X10050
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No heat on convection or bake. other functions operated fine
un plugged the oven. pulled the back cover off (3 screws). the heater terminations were there. removed heater wires. checked heater resistance with meter set on ohms reading was not correct. removed heater found a burned out place. installed new heater in reverse order of removal. works fine. If someone is a fare handy man this was a very simple task to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Remer from Dothan, AL
- Parts Used:
- WB20X10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Could not be turned on
Removed outer cover and then replaced the T. C. O. located on the left upper side if the unit. Replaced outer cover, tested oven. Oven operates normally.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from New Philidelphia, OH
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave would turn on ,BUT turn table would not turn and oven would not heat.
Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Tijeras, NM
- Parts Used:
- WB26X32629
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave would only heat food items to a warm condition
Removed microwave cover using screwdriver and anti tamper bit available at local hardware store. Megnetron had broken magnet making discovery of deffective part easy. Removed wire connector and three screws attaching magnetron to case, removed magnetron and installed new item in reverse order. Installed cover and made popcorn for operational check of microwave. Happy days..........
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Stone Harbor, NJ
- Parts Used:
- WB25X10019
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Burned out halogen bulbs
Used new rubber gloves so as to not get finger prints on the bulbs. Hope that was ok. Trying to use a paper towel was a nuisance. Also had to use a mirror to see the slots for the bulbs. This was actually a pain to do especially since I am short and was on my toes to do this. Only the bright light works and before there was a night light and a bright light. So there you have it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teri from Carmel, NY
- Parts Used:
- WB25X10019
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replaced burned out lightbulbs
Disassembled the bottom of the microwave in order to access the lightbulb sockets. Unfortunately, 1 of the 2 replacement bulbs broke during the installation process - 1 of the pins broke off while trying to insert it. Now I have only 1 bulb so the light is not as bright as it should be. It took me several trips the HomeDepot only to have to return the bulbs. Fortunately, PartSelect shipped the correct replacement bulbs the first time.
Was this instruction helpful to you?
Thank you for voting!