LVM1750DP2BB General Electric Microwave - Instructions

The order was easy and promptly received. I lowered the cover by removing retainer screws underneath. Simply lowered it and removed the broken glass and replaced it. The bulb was broken and the base of it was stuck in the socket. I didn't bother to remove it because the socket was brittle. I disconnected the socket by unplugging the wires, removing the retainer screws,and removing it. I replaced it with the new one. Screwed in the bulb. I replaced the cover and it was done. Ps: I used an Hitachi cordless screwdriver, which greatly helped when doing this alone.

Remove the microwave cover. Requires a phillips screwdriver and a torx security bit/nut driver (there are two security type screws on the back...guess they don't want you to do this at home!). I had to buy the a security bit set (about $7). The diode is easily accessible on the right side under the fan. Requires removing on small phillips screw and unplugging on electrical connection. GE provides some instructions in an envelope on top (after cover removed). There is a warning/instruction to discharge the capacitor before service. This was not a problem for me. Actual diode replacement took 30 seconds. Whole job = 15 minutes.

After discovering Parts Select website and reading the experiences and installation instructions of others with similar experiences, it gave me the confidence to give it a try. I order the parts, and in a few days, they arrived. I did the following, as read from others: 1. unscrewed the 5 screws on bottom panel of microwave. 2. Had wife hold panel while I unscrewed the 1 screw holding the lamp socket 3. Pulled lamp socket out of hole 4. Used needle nose pliers to pull wiring from old lamp socket 5. plugged the two wires into new lamp socket 6. removed old bulbs (which would have been a nightmare to do by just dropping down the bulb cover - bulb had been factored glued to lamp socket and even after I removed the glue, the bulb still broke when trying to remove the bulb - had to use needle nose pliers to unscrew the base of the broken bulb) 7. placed lamp socket with new bulb back into its slot and screwed the one screw holding the lamp socket back 8. screwed back in the 5 screws that held the bottom panel.

As suggested, I placed a towel over the stove. Only had 3 main screws to remove from bottom of microwave. Dropped the bottom and changed the sockets and light bulbs. After replacing the bottom tray, I put the new glass light lens in. The clips on glass holder bent back like a photo frame-really easy. Turned on the lights and was done.

Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.

Unplug appliance, Staring from the rear sides, remove the four side screws. Remove the left and right front screws and finally the front center screw. The bottom panel hinges down toward the rear . Unplug the input wires from the sockets . Unscrew the two retainer screws (one each) and pull the sockets out of the panel. Note that the retainer screws are shouldered. The shoulder fits through the elongated slot in the socket. Screw the bulb into the socket and insert through the mounting hole. Insert and tighten the mounting screws. Note that the sockets may appear to be a bit loose. That's OK because of the shouldered screw. Don't over tighten or you risk stripping the threads of the panel. Plug in the input sockets and install the panel screws in the reverse order of removal. Plug the appliance in and test the bulbs.

Opened the microwave oven door, unscrewed two screws which held the control panel on, then I removed two of the door switches (each had two screws), and then used the continuity tester to see which one was not operating. It turned out to be the secondary door switch, replaced it and to my amazement, the microwave worked. I have never repaired an appliance before but I didn't want to replace our over-the-stove built in microwave. It was the best day ever when it was working again! The hardest part was getting myself to try the repair.

Followed suggestion by previous poster to remove bottom panel...facilitated process well

Very easy to replace the light socket. Unscrew screws under microwave to lower the base. remove screw at rear of light socket. Unplug power to socket. Plug wire into new socket. Replace new socket into base and replace serew. Hold base plate up to microwave and replace all screws. Do yourself a favor, if replacing one of the lights, go ahead and do both. Shipping cost is the same for 1 or 2 bulb sockets.

every thing is working, but no hot

First, there are three door operated switches in this model. The monitor sw, the secondary sw (both of these are on the bottom in the same bracket) and the door sensing sw on top. The door sensing and secondary switches are both N.O. and have the same part number (probably why you show just two switches). The monitor sw is N.C. and it was not my problem. The secondary sw was bad on my oven but I had replaced the door sensing sw (which wasn't bad) on a previous order and kept the old one so I used it to make the repair. All three switches can be accessed without removing the oven by removing the discharge louver (remove two flat head screws on top and slide the louver to the left) then carefully remove the control panel (one screw on top and lift out). The switches are held in place by a plastic tongue that fits into the rear mounting hole on the switch. I used a common screw driver with a small tip to gently lift the tongue and slide the switch out with needle nose pliers. The new switch just snaps back in. The switch holder bracket looks like it would be easily broken so be gentle. I don't know what the symptoms would be if either of the other switches were bad so I would recommend buying all three and you would have them if one of the others failed in the future. The information I gave on the switches came from a schematic I found inside the control box. Hope this is helpful.

I tried to replace a light bulb over the cook stove without turning off the power supply. The light socket had deteriorated and the bulb base shorted out on the microwave frame. I ordered new sockets and bulbs. Replacing them was s simple matter with the power off. However, there was still no lights working with the power on. I pulled to cover off on top of the microwave (two screws) and checked the fuse. Continuity test showed it to be ok. Next I pulled the cover off the control panel and pulled out the mother board. On the back side I noticed two burnt pins. I applied solder with a solder gun to replace the burnt off solder. I put it all back together and it works fine.

I thought I could just unscrew the bulbs in the SpacemakerXL Microwave Oven. The bulbs melted into the bulb socket so every attempt to unscrew the bulb with pliers just broke the socket. So I took out the few screws holding up the bottom panel(with the bulbs and filters). I unplugged the electrical connection and took out the sockets but I used PAM Cooking oil on the electrical connections plugging into the sockets to avoid pulling the wire holders from the connection. Replacing both bulbs and the sockets at the same time makes sense since the heat from the stove melts the bulbs in the socket.

Microwave would not turn on. Lights and fan worked fine. Before the microwave stopped completely, it would turn the microware fan on even when door was open. I read the reviews and they were exactly the same issue that others were facing. Once I opened the front panel and got to the switches it was easy to figure out which switch was bad as it was the one that was soft (When clicking it). It was hard to take it out though (it seemed stuck). So, I used a plier to yank it out. I put in the new switch and everything worked just great! I would like to thank other comments that were left on the site to make my task much easier. Thank you (to the commenters on PartsSelect), you not only saved me money, but also ensured that I learn about the microwave more and give me the confidence that I could fix it.

Using a #2 Phillips screwdriver and removed the screw that retains the lens frame around the broken lens. I also did the same to the opposite side (whose lens was fine but the bulb had been burned out for some time). With my fingers I pryed up the frame clips that secure the lens in place, removed the pieces of the broken lens, and replace the lens with one of the new lenses I had ordered. Although the bulb on this side was still burning, I replaced it with one of the two I ordered anyway. When I removed the bulb that was burned out, the glass separated from the bulb's base. However, I simply put on a set of tight fitting leather gloves and used my ring finger to apply pressure inside the base and it soon began to twist and then came out. This takes a little manual dexterity, but is very doable. If it were too tight, you could take a large "easy-out" tool (like the one to fit a 3/8" - 1/2" hole) and it would remove the broken base in short order. I had also ordered a second lens, but the lens on the burned side was simply dirty, so I cleaned it, put it back in place and saved the new one for a rainy day. By the way, BE ABSOLUTELY CERTAIN THE LIGHTS ARE SWITCHED TO THE "OFF" POSITION BEFORE DOING ANY OF THE ABOVE. Also take care to clean the glass on the bulbs with denatured alcohol and handle them with clean cloth gloves or a tissue so as not to allow any oils to be on the surface when they are switched on. Body oil will immediately create a hot spot which will shorten the life of the bulb by at least 50% if not more.