JVM1740DM1BB General Electric Microwave - Instructions

lowered bottom panel, unpluged turntable motor, unscrewed one screw. replaced old motor with new alinged turntable button. repluged motor wire and finished.

This particular model has 2 hooks that are separate.

1. Remove the plastic trim on the inside of the door. Use a spatula and be care not to break any of the snapping parts. It will come apart.
2. There will be a metal trim that needs to be removed in order to get to the "screw" or "rod" that holds the hook in place.
3. All around the metal trim, there are plastic snaps. Use a screw driver to release the snaps from the metal trim.
4. My metal trim did not want to fully be removed... I was able to release the side where the hooks were and the bottom snaps.
5. Use the needle nose pliers to remove the spring. I found it easier to remove the bottom part of the spring to free the hook.
6. I had to pull on the metal trim enough to get the rod out of the hook so the hook could be removed. Very difficult with one person, but I got it done.
7. Put the spring in the new hook before you install it.
8. Put the rod back in, then the hook, then through the right hole.
9. Attach the bottom of the spring back to the lower hole.
10. Snap the metal trim back onto the microwave door.
11. Snap the plastic trim back onto the door.
12. Move the hooks up and down and feel there is tension. This should probably be done after Step 9.
13. Breathe!!!!

The filter we have is 6x4. I ordered by phone.They sent the wrong part - 6x11.
We returned it to Post Office at our own cost - $8.85 May26. Tracked - it arrived May 28. So far we do not have the correct filter. We are waiting for the refund. Charged $49.99 plus tax & shipping of $7.75.
Thank you for helping us get the correct filter and a refund. We should not be charged for returning the wrong part they sent us by mistake.
Marilyn Tostado

This microwave has two separate spring-loaded latch pawls. To get the broken latch pawl off and install the new one you first take off the rectangular plastic trim piece from the inside of the door to expose the pawls. There is a pin that secures the pawl in place. To get the pin out I had to carefully drill a regular hole bigger than the pin with the Dremel tool at the edge of the plastic door piece. I then could extract the pin with a small screwdriver or twizzers. The old pin and spring will come out and you reverse the procedure to install pawl and pin and connect spring. Then reinstall trim piece. I put a small piece of black electricians tape over the hole I made in the door edge. It doesn't show when door is closed and it blends well with the black plastic edge. Test to make sure microwave works and mine did after some carefully fitting of the trim piece.

Removed the screws in bottom of unit. Dropped down bottom and removed turntable motor mounting screw. Removed motor and replaced broken Coupler TT Hub from inside unit. Reversed procedure and rectified problem.

This repair was easy and could be done by anyone. If you undertake to do this replacement, remember to slowly bend the medal tabs back that hold the lens. Handled roughly these tabs could break off.

This repair can be don in under 5 minutes, easily !!

Removed old film, installed new horizontally and pulled it downward (match it along the top first). The cover required 2 "hooks" to be removed, only needed 4 clips. Used a screwdriver to remove the 2 clips.

Removed the control panel, one screw at the top. Removed 2 screws on the door switch holder and removed the door switch. VERY EASY.

Very easy replacement by taking off the plastic trim and than the front portion of the door. Unscrew the 2 screws holding the door handle. Both pieces just snap off from clips. Next pull the spring off the latch and slide the pin that secures the latch to the door. Install everything by reversing your procedures when taking apart completing the repair.

thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)

Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.

First I removed the bottom of the microwave, exposing the motor for the turntable. i then took the motor loose and removed the broken plastic coupler. I then put the new one in and re-attached the motor and bottom of microwave.

Replaced glass in frame and replaced lights

Simple. The parts came instantly. The glass was too big so I had it cut to size. I unscrewed the fixture with a screw driver replaced the bulb and slipped the glass cover into the frame and screwed the whole assembly in.

Screwed in new bulb.