JVM1540DM6WW General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Delores from Portland, OR
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Glass tray somehow got a nick in the edge, a few days later it split while in use.
Another company said the new plate would arrive in mid-March, this company seemed to be faster so ordered the tray here, and it came in less than a week. I put the turn button back in the center hole, set the wheeled ring on the bottom of the oven, fitted the new glass tray onto the turn button.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from ROSSFORD, OH
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Cooking Tray
Placed the new tray into the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Discovery Bay, CA
- Parts Used:
- WB06X10359
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
purchased a home that the microwave needed a grease filter
Used Google to locate parts dealers for GE.
Ordered from Partselect.
Part arrived a few days later and I easily put it in.
I thought the cost of this part was out of line but all others sold it for about the same.
Ordered from Partselect.
Part arrived a few days later and I easily put it in.
I thought the cost of this part was out of line but all others sold it for about the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from SANDY, UT
- Parts Used:
- WB27X10927
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Very loud noise when cooking
I opened it up, found there is sparks on the diode when cooking, I replaced the diode first, still no heat, I found all the switches and thermal stats were normal, there is 120V AC input to the transformer, so I tried to make a good guess and bought a Magnetron from Partselect, after I installed the new Magnetron, there is heat and the microwave is working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CLINTON TWP, MI
- Parts Used:
- WB15X24436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken handle
Pulled inner panel loose, removed screws set new handle replaced the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from DRUMORE, PA
- Parts Used:
- WB07X11007
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cracked vent cover
Just screwed 2 screws and it was done!very easy as was the ordering Thanks to customer service person!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessie from PLAQUEMINE, LA
- Parts Used:
- WB06X10712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fan cover was melted with holes.
Simple fix. Prayed old off with flathead screwdriver. Installed new in less than 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from DENTON, TX
- Parts Used:
- WB02X21661, WB24X10180
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
No heat
Also installed capacitor diode cable from first parts order. Used Phillips screwdriver to remove parts and reinstall. The original latch board becomes unusable when removing parts requiring the purchase of a new board. New parts did not solve the problem so it was a waste of time and money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from HORN LAKE, MS
- Parts Used:
- WB26X10240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The turntable motor was dead
For this under cabinet wall mounted unit you will need two people to remove it. There are two mounting screws inside the bottom of cabinet. Remove the two screws and lower the cabinet. Place it on a flat surface and remove the 8 screws
From the bottom of the cabinet. Then remove the two screws from turntable motor. Reverse the procesdure and the job done. Don’t forget to turn off power. Good luck!
From the bottom of the cabinet. Then remove the two screws from turntable motor. Reverse the procesdure and the job done. Don’t forget to turn off power. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from LONGWOOD, FL
- Parts Used:
- WB24X10180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Microwave with turn table and display present.
I followed the recommendations listed on the GE website for my model.
The cause of the fault was listed at 65% probable. I followed the suggestion, and yes it turned out the subject Interlock Door switch was my problem.
Working just fine now.
The cause of the fault was listed at 65% probable. I followed the suggestion, and yes it turned out the subject Interlock Door switch was my problem.
Working just fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darin from SAN DIEGO, CA
- Parts Used:
- WB27X35382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No heat. No unusual noise. Appers to function other than no heat
Multimeter checked/confirmed switches, sensors, and fuse first. All good. High power diode was bad - Replaced. Still no heat but now loud "MMMMM" noise when running. This means either the capacitor is also bad and/or magnetron.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from MIDDLETOWN, NY
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lawn mower would not start
removed cover over motor blew it out of leaves and dust. Removes 4 screws and removed piece ordered. The coil was rusted and not connecting. Changed oiece its working again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from CAPE CORAL, FL
- Parts Used:
- WB06X10712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic cover had quarter size hole burned
Use a butter knife to pop small plastic pin out and turn to remove. Used the metal pinwheel from old one and placed it back up in the microwave. Never heard of this being possible, but it seems to happen per the website and many other comments.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ira from LIVINGSTON, LA
- Parts Used:
- WB27X35382
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Food wouldn't heat up
Googled problem, removed diode, checked with meter and it was open, ordered new diode, checked new diode and it read open, installed. Any way, it didn't work. Went and bought new microwave!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from LAFAYETTE, IN
- Parts Used:
- WB06X10712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stirrer fan cover was melted
This repai me couldn’t have been simpler! I noticed that the stirrer fan cover on our microwave had melted areas. My husband suggested we just buy a new microwave. As the handywoman of the family, I searched online to see if it was a fix that I could handle. I ordered a part for less than $20 and fixed it in about 30 seconds! All I had to do was pop out the plastic screw, put the fan in the new cover, and pop it back into place!
Was this instruction helpful to you?
Thank you for voting!