JVM1860WD002 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bill from Bronston, KY
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drive motor failed
I removed the screws (7) around perimeter of bottom. Don't remove the middle screw as it holds some gizmo in place. Dropped down hinged bottom. Removed motor (2 screws and a plug) matched to picture on website and ordered.
2 days later, part arrived, installed, good to go.
Bill, Kentucky
2 days later, part arrived, installed, good to go.
Bill, Kentucky
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Blakely, PA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My turntable stopped working
I read several customer reviews before starting the repair. Removed the old drive motor to make sure I was ordering the correct part. Removal consisted of removing the screws on the bottom plate, disconnecting the electrical plug from the motor, and removing the one screw that attached the motor to the housing. Installation of the new motor was the reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Tucson, AZ
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass cooking tray stopped rotating
I removed the microwave oven from the wall by unscrewing a trim plate or frame that surrounds the face of the oven. Pulled the oven out of the cabinet. Removed the glass cooking tray and rollers from the oven interior. Turned the oven on its side to expose the bottom. I unscrewed the small cover plate in the middle of the bottom which exposed the turn table motor. The motor was attached by two screws and a connector plug. In a couple minutes I removed the motor and replaced it with the new one and reassembled the oven. I put it back in the cabinet and it works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Highlands Ranch, CO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable quit working
Took the bottom of microwave off unplugged motor replaced it with new one (two screws) plugged it in replaced bottom and ther you go saved $240.00 over the local appliance repair company. Thanks Mike,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Placentia, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy turntable. (grinding)
Nice. Half dozen screws drops the bottom, 2 screws on the motor, pop in the new, reassemble and throw in the popcorn. (Was skeptical. Have replaced quite a few of these little motors in data centers. Common part in high-speed printers. Never saw one fail like this but your feedback convinced me otherwise.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maureen from Yorba Linda, CA
- Parts Used:
- WB06X10224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack holder was catching fire.
Removed the damaged holder by pulling it out. The new one went in with ease. This sure beat the $90 quoted to us to have a GE repair person come to the house. The part was under $7 and under $16 total for shipping. I think we were fortunate to be able to order this part on-line.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith A from LAKEWOOD, CO
- Parts Used:
- WB36X10163
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb went out
Opened the light cover. Removed the old light bulb using a light tug on the old bulb, lined up the new bulb and pushed gently into the socket.
Turned the power back on and the microwave is good to go.
Turned the power back on and the microwave is good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kip from POWELL, OH
- Parts Used:
- WB27X10928
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Not heat
-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from North Port, FL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Tray motor stopped working
Removed the cover, 6 screws and then the motor, 2 screws. Unpluged the old motor and just reversed the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRUCE from MONROE TWP, NJ
- Parts Used:
- WB06X10144
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
part was cracked
removed old part and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janice from GOLD RIVER, CA
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I thought I had pushed the timer button for 20 minutes duration period,
however, I had hit the cook button and the microwave did not have an item to cook inside. Resulted in shattering the glass tray and meting the plastic lid sitting inside which was fused to the cooking tray. Carefully wrapped up the shattered tray and melted lid in heavy paper, deposited it into the garbage, then happily placed my new E.O.M. glass cooking tray into my G.E. Profile microwave. Thank you .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Cincinnati, OH
- Parts Used:
- WB02X10733
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water dipenser valve leaking.
Replaced the filter cartridge.Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from LEWISTON, MI
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The center of turn table broke. A small plastic part that goes under the glass in center.
We took out the broken part, it came right out,and put new part .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MABEL from GILROY, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable would not turn
took off steel plate---removed two screws--unpluged drive motor--replaced with new drive motor. reversed removal procedure . Took about 10 minutes.
Great service from PARTSELECT.
Great service from PARTSELECT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARBARA from PORTSMOUTH, NH
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn Table Stopped Working
Very easy repair I did not even have to take the microwave down. Just removed the 7 screws, the bottom swung down removed the 2 screws holding the motor, unplugged it put the new one in put the screws back and Done.
Was this instruction helpful to you?
Thank you for voting!