JVM1490SH01 General Electric Microwave - Instructions

Buying the bulb and doing the replacement my self was the best thing I had done. The same problem happened last year and I had the American Home shield insurance at that time so I called the company and they took three weeks between ordering and replacing the light, they showed me the final bill and it was $240.00....!!! This time I bought the light through partselect, got it within 48 hours and did he replacement myself within 15 min, I followed the instructions on the video and had to do an extra step ( due to the model I have) but I was able to replace the bulb and yooohooo it was working when I reconnect the power... I am a person who never tried to fix any electrical appliance before, but after this experience I will always try to do it myself... Believe me if I can do it and felt it was easy you can do it.... Thank you Partselect.... I can't speak high enough about you

Snap the plastic trim piece from the inside of the door off.took broken latch out and put the new one in.PS your part came really fast.Thanks

Unplug the microwave. Remove front grill and cover by removing 2 screws on top of microwave. You have to look down from the top. I could not locate the screws by feel. Once the two screws are out, remove the grill by sliding slightly to the left to lift out. Open the oven door to facilitate removal. Then remove the steel light cover (1 Phillips screw in the center of the unit) and unclip the bulb holder on the right. Do not touch the halogen bulb when you replace. Reseat the bulb holder and test by plugging in the unit with the door open. Unplug and replace the light cover and grill.

I had left the door to the microwave open and turned around and hit the door latch assembly with my arm, sanpping off the bottom latch hook. In an effort to take apart the latch assembly it was necessary to take off the door choke cover and in doing so I sanpped a few of the plastic tabs that hold it in place. Undismayed, I then went online, found PartSelect, ordered the replacement parts, received them in three days and in fifteen minutes fixed both of them. The diagrams on the site made it easy to find what I needed and ordering the parts was easy. Thanks PartSelect-my wife is happy again!!!

I used a phillips screwdiver to open the light cover protecting the halogen bulbs (2) both had burned out and needed to be replaced. A bit akward to replace, but within 5 minutes both were removed. I called your part service department to order replacements,(friendly and courteous service I might add!)was told that they would arive in about 3-5 days. 1.5 days later they were on my doorstep...They were promptly plugged into my GE underhood mounted microwave, now I am back in service! You've won me over and I will tell all my friends about you. Thanks again!

Took item from sealed box and removed protective bubble wrap. Placed tray in microwave, aligning tray with turntable sprockets. Perfect fit, perfect match! And the part arrived in three days and was very competitively priced. What more is there to stay? Will use PartSelect for other replacement parts. No brainer!

Removal of the bulbs was easy; reinserting was not as easy due to the configuration/placement of the bulbs in the unit. It was interesting that a simple suggestion to keep the bulbs covered with some of the packing material made sense as to not directly handling the bulb itself and causing any contamination of the bulb(s).

Placed the new tray in the microwave.

My daughter hand installed bulbs without a problem, took a minute and used a phillips to reinstall the cover. I shopped on-line because I wasted two hours between Lowe's and Home Depot trying to get the right bulb. I did think your postage was crazy high, otherwise glad to get the right bulbs to solve the problem.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

Found a service manual on-line, and read some blogs that indicted the Thermal Cut Out devices that are basically thermal fuses. I removed the device from over the range, which turned out to be not 100% necessary, but made the repair much easier. Found that the Cavity TCO was certainly burnt, and tested bad with an Ohmmeter. The Hood TCO tested open, so I assumed that device was bad, which turned out not to be true. The TCO's are one shot, so I found PartSelect in a search engine, and entered my product model number. The parts were all clearly identified, so ordering was easy. Replaced the parts, bench tested the repair and re-installed the device. Way cheaper than a service call and I also replaced the long burnt out vanity light. This bulb burnt out in less than a year, but a serviceman had told me that the entire device had to be dis-assembled to replace the part, which is not true. This part can be replaced without removing the oven from the over-the-range mount, as can the three TCO's in the oven.

Take the pliers and place a tight grip on the broken rack bracket, twist toward front of microwave until loose, pop out and by hand insert new rack bracket, twist toward the back of microwave until fully in place. One side was slightly harder than the other taking off and replacing rack bracket.

Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.

The instructions for removing and installing the new bulbs appear to be great; however, nothing tells me how to remove the microwave from the mounting so I can then invert it and take care of the bulb issue.

My son said order it. It came a day later. Very cool. He took the door off and up to his room. No idea what tools except most likely a screwdriver. I asked him how did it go. He said it's good. Nice...