LVM1750DM2WW General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DAVID from IRVINE, CA
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dropped and broke the cooking tray
New one arrived very quickly.
Right part. Right on time. Fit like it should.
Excellent service.
Right part. Right on time. Fit like it should.
Excellent service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Florence from Lake Forest, IL
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tray cracked after only 4 months of use
Replacement tray was installed. It was larger than the original tray, but it fits in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard Gayle from Fairhope, AL
- Parts Used:
- WB02X11265, WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Undercounter light on microwave broke off and I damaged thescoket and bracket trying to get bulb out. All had to be replaced.
Unscrewed bottom of unit; dropped it down. Replaced bracket, scocked and bulb. Easy job with the right parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Leesburg, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
NO light
.Thank You Dan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from GILBERTSVILLE, PA
- Parts Used:
- WB36X10071
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass light lens cover was cracked
I first read the previously posted directions from other customers that were sent with my part order confirmation, which were all very helpful. Then, I basically used a screw driver to unscrew the screw holding the lens cover in place - be careful as it is a very tiny screw and it can easily fall behind your oven. You might want to place a large piece of cardboard over the space between oven and wall, as I did, so that you don't lose the screw in case it falls. Next I pried open the prongs, carefully slid out the cracked lens, and slid the new lens in place, pushed back the prongs and put the screw back in. I found that it was easier to use my fingers to first place and tighten the screw because it is very small and will keep falling out of place if you try to just use the screwdriver. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from LINCOLN, CA
- Parts Used:
- WB08X10016
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Remove old light sockets and replace in Microwave over stove
Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from SEASIDE, CA
- Parts Used:
- WB36X10071, WB36X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Glass lens and two light bulbs replacements
My microwave is built in above the stove which provides lighting and fans for my stove. The glass lens cover for the lighting was cracked in several places and the light bulbs had burned out. I taped the glass lens for removal so it didn't break apart due to the cracks Removed the one screw. .Both light bulbs broke away from the base sockets as I tried to unscrew them. I used electrical tape wrapping in reverse on a lightbulb (socket end) so it was sticky for a grip on the base, shoved it in the sockets and was unable to unscrew the broke off bases. So it was very successful and no repair man was needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from FISHERS, IN
- Parts Used:
- WB06X10420
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Turn table stopped rotating.
I tried to install the new part several times, but it didn't work. So I used a pencil to move things around down the shaft. After that the new part went in and now my microwave is doing what I need it to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Fort Worth, TX
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Batavia, OH
- Parts Used:
- WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Light Socket
Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from CHESTERFIELD, VA
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no lights on microwave
ordered 2 new sockets and bulbs easy replacement great service from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- regina from weston, FL
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rotating plate broke
bought a replacement for it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from WICHITA, KS
- Parts Used:
- WB26X10208, WB06X10420
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My turntable quit working
I replaced the turntable motor and coupler. It did not fix the problem. Not sure where to go from here. Looks like the next step involves parts that are as expensive as a new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Muncie, IN
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave Quit working but lights worked
llation
Was this instruction helpful to you?
Thank you for voting!
Still runs even the door was open
Pulled it from the wall remove the front vent covers removed the control panel remove the door switches by a special screw driver bit which looks a star remove the electrical terminals pressed the plastic clip pulled the switch replaced it with new one then followed initial steps backward
Was this instruction helpful to you?
Thank you for voting!