PVM1870DM3WW General Electric Microwave - Instructions

Once we figued out that you had to remove the panel underneath the microwave, pull down the turntable motor part and then insert to coupler it went really fast. Through trial and error we figured it out, but should have checked for installation instructions on the internet. Repair time would have been less than 15 minutes.

Pull cover off , located the bad magnetron . Then replaced it with the new one. About 15 min. Of work.

I replaced the cover just fine but i think a sensor went bad

every thing is working, but no hot

Loosen the two long anchor bolts that screw into the top of the microwave cabinet. These are usually in a shelf or cabinet directly above the microwave. Tilt the microwave forward enough to remove the 2 Phillips head screws from the top of the microwave cabinet. They are near the front. When these two screws are out, remove the fan vent. Once the fan vent is off, remove one screw that holds the control pad in place. Let it hang down. Just to the left of the control pad, you will see wires leading to three switches that close when the door is closed. Use a torx driver to remove the two screws that hold the switch bracket in place. With the bracket out, unplug the wire harnesses. On the opposite side of the wiring connected, a tab holds each switch in place. Lift the tab and slide the switches out. Usually, the bad switch will be identified by a loose or broken spring. Test them by pressing down on the switch. If you notice the bad switch spring, this is usually the bad one. When you have the new one, simply push it back into the appropriate slot and be sure that the holding tab snaps back in place. Plug the wires back in and re-attach the bracket. Put the control pad back on, then the fan vent. When down with those, push on the bottom of the microwave to lift it back into place and tighten the two anchor bolts in the top.

First, unplug microwave. Unscrew two screws at top of microwave, slide grill cover left and remove. This allows access to single screw holding control panel. Remove this screw and lift up control panel to remove. Secondary door switch is black switch at lowest position. The switch is held in place by a lever in back and very hard to get to. Remove the wires plugged into the switch, then remove two screws holding the plastic switch mount that holds all three switches. These screws use a "star" type screwdriver. Once the plastic mount is free, lift it up, right, and tip it slightly to find the lever that will release the black secondary door switch (the lowest switch)...release the broken switch, snap the new switch in its place. Replace the plastic mount by lifting and replacing back into position and replace the two "star" screws. Now, replace the wires onto the new switch, and test operation. Replace control panel, and top grill. It goes faster than it writes...getting the old switch out through that difficult to reach lever was the hardest part...still less than thirty minutes.

Uninstalled microwave from above range, removed cover then vent assembly (slide slightly to the left to free it). Opened the control panel (slide up then tilt forward) to access the troubleshooting/repair/test sheet. Followed the diagnostic flowchart and determined the TCO above the cooking cavity had failed. No other faults found. Ordered part Sat. afternoon and rcvd it Monday. Part is held in place with spring clips and quick connect terminals so installation was easy. Microwave was back in operation in no time.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

It was a snap using the instructions given. The key is getting into the unit. I did have to use a multimeter to find the failed switch since there are two of that type.

My son fixed it in less than five minutes! easy!

Microwave would not turn on--No lights--Nothing worked 1. Removed screws from back and side and pull off microwave cover. Be careful! There HIGH voltage back there due to a large capacitor that stores power. This capacitor is charged up even with Microwave unplugged. I checked the fuse located on top back part of Microwave. A lot of the time this is the problem but this time the fuse was good. I used an Ohm meter to check to see if there was an open circuit in one of the Thermostats. There are two of them in the Microwave. The Thermostats are about the size of a dime. One is located on the top right side and the other is on the top left side. One of them was bad. I ordered a new Thermostat. It arrived in just 2 days. I installed it and the Microwave was repaired and working great.

took part of put new part on.30sec to do.

Trouble shot first by removing the digital read out face plate panel, lifting it up and out. Found the thermostat housed on the bottom section (found a picture of what I was looking for). It had two connectors. Removed the connectors and noticed that the one looked burnt/melted that was on the thermostat. Took paper clip, connected it with the wires to bypass the thermostat. Plugged in the microwave and power returned. Yes! Ordered thermostat part and changed it out. The new part didn't have a piece that fit exactly into the floor of the microwave so I just made sure it was secure to the bottom. It is only attached by 1 small screw. Fixed!

removed the bottom of the microwave and removed the motor and replaced the coupler and reassembled. Easy repair.

thank you very much.