PVM1870DM2WW General Electric Microwave - Instructions

removed access panal, found soft switch as discribed on your web site. removed and replaced.

Simple, simply lifted the old piece out of position and dropped the new piece in. A small part of the broken old piece must have fallen away and is still in the unit, but it has not gotten in the way of the new piece doing its purpose

Installation of the damper was effortless but removing the microwave, cutting holes vertically through an overhead cabinet then installing ducting with a ninety degree bend, through another cabinet, and then through outside wall consumed most of the time and effort.Your service, packaging, and timely (next day!) were extremely helpful.

removed the bottom of the microwave and removed the motor and replaced the coupler and reassembled. Easy repair.

My son fixed it in less than five minutes! easy!

Microwave would not turn on. Lights and fan worked fine. Before the microwave stopped completely, it would turn the microware fan on even when door was open. I read the reviews and they were exactly the same issue that others were facing. Once I opened the front panel and got to the switches it was easy to figure out which switch was bad as it was the one that was soft (When clicking it). It was hard to take it out though (it seemed stuck). So, I used a plier to yank it out. I put in the new switch and everything worked just great! I would like to thank other comments that were left on the site to make my task much easier. Thank you (to the commenters on PartsSelect), you not only saved me money, but also ensured that I learn about the microwave more and give me the confidence that I could fix it.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

simply remove broken coupler and install new coupler. no tools required.

We put the new glass lens in the metal frame and screwed the frame in under the microwave. Easy, breezy! Like new condition!

I followed the online instructions.

Threw the old filter away and slide the new one in without any tools ! Filter should be cleaned every month - who knew ?

1. Unplug the microwave or switch off the breaker to the microwave. 2. Unscrew 5 screws on the bottom plate of the microwave. The plate swings down by the hinges on the back. 3. Unplug the wires leading to the turntable motor and make note of which color wire goes on which side of the motor plug. 4. The initial instructions said unscrew the screw holding the motor but my model has two screws. Remove the screws and lower the motor. 5. Insert the plastic coupler from inside the microwave through the hole in the center of the base. The coupler has a half moon shaped female shaft that connects to the male shaft that extends up from the motor. Slide the motor shaft into the plastic coupler. 6. Replace the screws that hold the motor onto the base of the microwave. 7. Plug the power wires back into the motor with the wires in the correct position as noted above. 8. Plug in the microwave and turn it on to check if the turntable now turns. Mine did not at first so I unplugged the microwave and the motor wires. It turns out you can plug the motor wires in and they don't connect correctly. I reconnected the motor plug and plugged the microwave back in and turned it on. This time the turntable was working. 8. Replace the five screws on the bottom plate of the microwave. Done.

removed housing. saw t-stat was burnt. replaced t-stat by removing mounting screw and installing new t-stat. reinstalled mounting screw. reinstalled oven housing. 15 minute job.

This is the second time this happened for me. The shaft for the Coupler breaks and will no longer let the plate turn. I looked at the instructions of letting the bottom of the microwave down, etc. and all I could think of is I don't think so. I used the tweezers to try to get the broken piece of the coupler but neither time was it intact. Could not locate the broken part so took the liberty of just putting the new part on the shaft, pushed down and viola I now have a turning table again. I am an 83 age female who likes to try being a do-it-your selfer. Of course there are times I am not successful but. . .By thinking back of why this part keeps breaking I think it may be my fault. I always turn the glass plate around manually when the handle of the cup or mug is out of reach. May be my fault and maybe not. Anyway this time I ordered 2 of the same parts just for future repair hopefully not needed. V.J.

Once we noticed the turntable not working I removed the piece and noticed it was broken at the base of the coupler, took a vacuum and removed the broken piece and installed the new part. Thanks for the help!