PSB1000NWW01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert L. from Racine, WI
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lamp burnt out
We had our kitchen remodeled; new cabinets, countertop, range, refigerator, microwave, dishwasher and floor.
The cabinets around the microwave were custom made; it looks great but it hid the screws, which had to be unscrewed to remove the grill so the interior light of the microwave could be replaced.
A stand was used to support the microwave as I lowered it so the screws could exposed so the light could be replaced.
The light was replaced, the microwave was raised back into place and all is well. I replaced the bulb while my wife was out of town. When she returned she noticed that the microwave was nice and clean; she was NOT aware of the fact that the bulb was replaced!
Bob
Racine, WI
The cabinets around the microwave were custom made; it looks great but it hid the screws, which had to be unscrewed to remove the grill so the interior light of the microwave could be replaced.
A stand was used to support the microwave as I lowered it so the screws could exposed so the light could be replaced.
The light was replaced, the microwave was raised back into place and all is well. I replaced the bulb while my wife was out of town. When she returned she noticed that the microwave was nice and clean; she was NOT aware of the fact that the bulb was replaced!
Bob
Racine, WI
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darren from Madison, CT
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Halogen light for the Microwave above the stove went out.
Ordered the part. 2 days later part arrives. Took me 30 seconds to install the part. Sorry it was not more eventful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from PIEDMONT, CA
- Parts Used:
- WB26X32629
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
runs but does not heat
I removed the main cover ( torx security bit required) and tested the magnetron, capacitor, diode and door interlock switches according to instructions found on the internet. The capacitor and diode tested good but the magnetron looked burnt and corroded on the tip. The magnetron I received was an exact replacement for the original. It was easy to replace the magnetron which arrived in 2 days standard shipping. I also cleaned the fan while I had access to the inside area. Hoping to get another 18 years use from the microwave!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Berwick, PA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Halogen nite light bulbs had burned out
Parts arrived on the morning of the second day (Saturday) to my pleasant surprise. I opened the nite light access door with a screw driver. Inserted the 2 bulbs without touching the outside of the halogen bulbs. Checked that the bulbs did work and closed the access door. The entire process went quickly and posed very little difficulty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pete from roslyn, NY
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both undercabinet light bulbs blown
1. Open the cover over light bulbs with screwdriver.
2. Pulled out blown bulbs.
3. Inserts new bulbs from Partselect.
4. Tested new bulbs
5. Closed the cover over light bulbs with scvrewdriver.
6. Threw out old bulbs and packaging material.
Now, was that easy or what!
2. Pulled out blown bulbs.
3. Inserts new bulbs from Partselect.
4. Tested new bulbs
5. Closed the cover over light bulbs with scvrewdriver.
6. Threw out old bulbs and packaging material.
Now, was that easy or what!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Florentino from West Palm Beach, FL
- Parts Used:
- WB21X10148
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Power
Check with Digital meter all connections.Find a Thermostat open loop.This thermostat is near the Megatron .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES T from PEWAUKEE, WI
- Parts Used:
- WB27X10856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Display did not lightup but the microwave oven functioned.
I did not have to replace the part. I turn the fuse off and waited 5 minutes and turned it back on. The display came back on. I saw this recommendation on your web site after I ordered the part. You should do this before you order the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Bessemer, MI
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
mICROWAVE WOULD NOT HEAT
I REMOVED THE TOP PANEL OF THE MICR0WAVE AND THEN REMOVED ONE SCREW TO REMOVE THE CONTROL PANEL. rEMOVED OLD SWITCH. SNAPPED IN NEW SWITCH AND CONNECTED WIRE. REPLACED CONTROL PANEL AND UPPER PANEL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from MAGNOLIA, TX
- Parts Used:
- WB06X10638
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The part was burnt and was causing sparking inside the microwave
Removed the old canopy mica, it has tabs that slip into slots on the top of the microwave. Then installed the new part, the tabs are inserted into the same slots.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Orient, OH
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light burned out
removed screw that holds glass for light and replaced bulb.
Reinserted screw that holds glass.
Only down side was cost to ship small bulb.
Reinserted screw that holds glass.
Only down side was cost to ship small bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from PONCA CITY, OK
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from LOUISVILLE, KY
- Parts Used:
- WB26X10193
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable motor was making noise
Unscrewed and dropped the bottom panel of the Advantium on its rear hinge, disconnected the light and the motor, removed the motor screws, and replaced the motor. Very simple.
However, not related to the Advantium or the motor, trim had been applied to the bottom of the wall cabinets after installation of the Advantium. This trim prevented the lowering of the panel (and future removal of the whole oven), so I had to chisel and file and repaint the trim to get it out of the way.
However, not related to the Advantium or the motor, trim had been applied to the bottom of the wall cabinets after installation of the Advantium. This trim prevented the lowering of the panel (and future removal of the whole oven), so I had to chisel and file and repaint the trim to get it out of the way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from harbor springs, MI
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Halogen lamps did not light-burned out
Removed the light cover screw with a Phillips screwdriver. Removed the lamps from the packaging just enough to free up the 2 prongs for fitting in the socket. Make sure the power is in the "off position". Install the bulbs one at a time by lining up the 2 sockets (Very important not to touch the halogen bulb glass surface while installing them). Energize the light switch to check operation of the new bulbs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from DENVER, CO
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Microwave not turning on. All other functions operate
DISCONNECT THE POWER CORD and discharge the capacitor
Leave unplugged overnight
Remove vent grille by removing the 2 philips screws
Remove the LED panel by removing 1 phillips screw
Disconnect all connectors that plug into back of the LED board completely
Remove the wires from the switches (3) at the inside edge of the microwave door
Gently remove each switch housing and test all three switches for continuity
Carefully replace non-functioning switches and reassemble the panel
GOOD LUCK
Leave unplugged overnight
Remove vent grille by removing the 2 philips screws
Remove the LED panel by removing 1 phillips screw
Disconnect all connectors that plug into back of the LED board completely
Remove the wires from the switches (3) at the inside edge of the microwave door
Gently remove each switch housing and test all three switches for continuity
Carefully replace non-functioning switches and reassemble the panel
GOOD LUCK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Mount Sinai, NY
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both my microwave halogen lamps went out.
Using a phillips screwdriver I opened the panel in which the two lamps are located and easily removed the lamps. I ordered them through the internet and was pleasantly surprised when I received them the next day.
Was this instruction helpful to you?
Thank you for voting!