PEB206CSN1SS General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sandra from Kosse, TX
- Parts Used:
- WB26X10143
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Turn Table Didn't Work Every Time.
Remove tray and rotating ring assembly. Turn the microwave onto the back. Locate the center plate and cut it loose with the side cutters. (Note: there are retaining slots on the opposite side) these slots hold the cover plate in place when reattaching. Use a magnetic phillips head screw driver so you don't drop the cover retaining screw. After cutting loose the cover, unplug the wires from the motor. (Note placement for correct reattachment). Remove 2 screws and remove old motor. Replace motor. Replace the screws and reattach the wires. Replace the cover (rotate so the prongs fit into the slots) tighten screw; you're done!!! I ordered the rotating ring, but I don't need it. Now I have an extra.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ira from LIVINGSTON, LA
- Parts Used:
- WB27X35382
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Food wouldn't heat up
Googled problem, removed diode, checked with meter and it was open, ordered new diode, checked new diode and it read open, installed. Any way, it didn't work. Went and bought new microwave!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from JACKSON, TN
- Parts Used:
- WB36X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The Light Bulb went out
I used a phillips screw driver and a special type bit to undo the screws from the cabinet and found the light bulb and took the old one out and put the new one in and put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darin from SAN DIEGO, CA
- Parts Used:
- WB27X35382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No heat. No unusual noise. Appers to function other than no heat
Multimeter checked/confirmed switches, sensors, and fuse first. All good. High power diode was bad - Replaced. Still no heat but now loud "MMMMM" noise when running. This means either the capacitor is also bad and/or magnetron.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Wesley Chapel, FL
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable Stopped Working/Display Timer Would Countdown But Not Heat
With this model, you must remove the outer covering. Don't try to access the display unit from the front like I've seen in some other GE microwave videos. After removing the outer covering, the switches are easy to replace. They are very visible and easy to get to without taking any other parts off. You will see the door switches just behind the display board. Remove the switch and then remove the connecting wires to ensure you don't inadvertently brake a wire. You will need a tamper resistant star bit to remove 3 or 4 screws from the back panel. All other screws are philips head. I went ahead and replaced both switches (yes...there are two of them) and works like a charm. I saved an $800 microwave for less than $60 and know what to do if it happens again. Appears to be a common problem on this model. Thanks for others making a post...It saved me time and money reading others remarks. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from BRENTWOOD, NH
- Parts Used:
- WB36X10063
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bulb burned out
Removed outer cover, Cash with for Phillips screws as I recall, Then remove six or eight safety screws with Phillips special bit. Pulled bulb, cover back, removed, and replace bulb, back together all set
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from FULSHEAR, TX
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
M/W would not start. control panel OK
unplugged power
removed main black cover.
located part WB24X10047 and replaced
removed main black cover.
located part WB24X10047 and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from BOZEMAN, MT
- Parts Used:
- WB36X10063
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
light bulb burned out
Remove the top of the microwave, regular phillips screws on sides, torque screws on back. Lift up back and slide off cover. Light bulb socket is easily detached and bulb unplugged and replaced. Slide cover from back lifted slightly so lip will slide into front of microwave, than replace screws. Be sure to unplug microwave before you start.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- johnny from port orange, FL
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
no power in microwave in turn table wouldn't turn light would work act like door was open
remov cover to check voltage and found problem at the interlock switch ohm the switch and found it was open replace both switches it work fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LAFAYETTE HL, PA
- Parts Used:
- WB06X10633
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken wheel
Swapped new part with broken part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from BLUFFTON, SC
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
The unit would run when the door was open!
First I had to accept the fact that the unit was designed to keep non-professional people from doing any repairs. The switch was installed in such a manner that I had to break the mounting to remove the switch, then drill a hole in the mounting to secure the new switch in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Jacksonville, FL
- Parts Used:
- WB49X10189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I accidentally dropped the tray to the floor glass pieces got everywhere so it broke. Thats why I ordered a new plate.
Just to replace it as it was just a plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from New York, NY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat
Replace the fuses
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mack from Jacksonville, FL
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
No heat.
Replaced the fuse. Result; did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from Santa Barbara, CA
- Parts Used:
- WB06X10633
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
original rotating ring assembly was broken
Removed broken assembly and set the new assembly in place
Was this instruction helpful to you?
Thank you for voting!