JVM1540DN2BB General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Still runs even the door was open
Pulled it from the wall remove the front vent covers removed the control panel remove the door switches by a special screw driver bit which looks a star remove the electrical terminals pressed the plastic clip pulled the switch replaced it with new one then followed initial steps backward
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Muncie, IN
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave Quit working but lights worked
llation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from WICHITA, KS
- Parts Used:
- WB26X10208, WB06X10420
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My turntable quit working
I replaced the turntable motor and coupler. It did not fix the problem. Not sure where to go from here. Looks like the next step involves parts that are as expensive as a new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Littleton, CO
- Parts Used:
- WB36X10071, WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
glass light lens was broken, had collected grease, was dark.
Simply removed screw, pulled down light holder, unfoled the metal tabs, took out the broken pieces and replaced the glass lens and light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- regina from weston, FL
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rotating plate broke
bought a replacement for it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from FAYETTEVILLE, AR
- Parts Used:
- WB06X10596, WB36X10071, WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cracked Light Lens, Burned Out Bulbs
Easy peasy - removed lens holder w/screw driver. Cleaned cover after removing damaged glass lens. Then unscrewed burnt out light bulbs. Installed new bulbs, slid in new light lens into holder and screwed back into bottom of microwave. Removed greasy filter and slid in new filter. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KAREN from MANSFIELD, MA
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light lens broke a couple of years ago
unscrewed the screw, pried up metal tabs that hold in light lens. took out broken pieces, slid in new light lens re-secured tabs with fingers, screwed in the screw again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- myron from ARDMORE, PA
- Parts Used:
- WB07X11034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The grille kept falling off. The protrusions that the screws passed through had cracked off.
The grille does not come with screws, so keep the two that held the old one in place.
Was this instruction helpful to you?
Thank you for voting!
Microwave will not start
Removed three screws from the top front cover and slide it out and following I removed the touch panel and the housing that holds the switches and replaced the bad one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Columbia, TN
- Parts Used:
- WB06X10420
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Coupler broke at shaft & motor seized
Removed 5 philip head screws from under panel. Under panel droped down exposing drive motor. Removed one drive motor screw, replaced with new motor at the same time lining up new coupler. Pressed together, reinstalled motor srew, attached wire coupling and tested. Worked fine. Reinstalled lower panel screws (5)and unit was ready to go. I ordered two of each units because I believe this to be weak link in the unit. It was only 2 years old, used little as I have another home. I recently installed a like unit (Hanging) and it was a breez. 4 srews properly placed, electrical cord hole properly drilled & ready to go in 45 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Fredericksburg, VA
- Parts Used:
- WB06X10420
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My Turntable Coupler was broken
I took the glass table up and underneath was the turntable coupler. I reached in with my hands and gently pulled the old coupler out. Once out I lined up the new one and gently pushed it in the hole until it locked into place. The process took about 5 minutes to complete. Very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Cutler, ME
- Parts Used:
- WB06X10420
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Micro turntable would not turn
Removed the screws in bottom of unit. Dropped down bottom and removed turntable motor mounting screw. Removed motor and replaced broken Coupler TT Hub from inside unit. Reversed procedure and rectified problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from TREASURE IS, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Under the microwave there are two light bulbs that light up the top of the oven/range.
Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norman from Voorheesville, NY
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken lens
remove two screws bend out flaps remove broken glass install new glas bend flaps back to hold glass install two screws. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Raleigh, NC
- Parts Used:
- WB06X10420
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable motor burnt out
lowered bottom panel, unpluged turntable motor, unscrewed one screw. replaced old motor with new alinged turntable button. repluged motor wire and finished.
Was this instruction helpful to you?
Thank you for voting!