JVM1540DM4WW General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ransford from LAUREL, MD
- Parts Used:
- WB26X10240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Turntable not rotating
Replaced the dead motor with new motor . I used YouTube video to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stella from BRADENTON, FL
- Parts Used:
- WB06X10712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burn hole in cover
My Son -in- law did it, removed the pivot pin removed the Cover and fan blade by turning it counter clockwise , Then replaced fan blade and cover and turning it clockwise and replaced the pivot pin .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Hyannis, MA
- Parts Used:
- WB26X10240
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Turn table did not rotate
Removed the original synchronous motor and replaced it with a new one. It turned on and rotated for about 1 day and stopped. I tested the motor for continuity and it was good. I need help in further trouble shooting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karina from RIDGEFIELD, CT
- Parts Used:
- WB24X10181, WB24X10180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave was not heating and not turning.
I unplugged the appliance first. It was an over the range microwave so I only opened the front part where the buttons are, and behind it there’s a set of 3 door switches, carefully took out the burned down one and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from DENVER, CO
- Parts Used:
- WB06X10704
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plate wasn't spinning.
Simply popped the turntable shaft in. It was installed by hand, no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from ROSSFORD, OH
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Cooking Tray
Placed the new tray into the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Discovery Bay, CA
- Parts Used:
- WB06X10359
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
purchased a home that the microwave needed a grease filter
Used Google to locate parts dealers for GE.
Ordered from Partselect.
Part arrived a few days later and I easily put it in.
I thought the cost of this part was out of line but all others sold it for about the same.
Ordered from Partselect.
Part arrived a few days later and I easily put it in.
I thought the cost of this part was out of line but all others sold it for about the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from MEDFORD, NY
- Parts Used:
- WB06X10704
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass Turntable not rotating when microwave oven ON
Turntable shaft was worn and out of shape likely due to heat. Simply remove rotating glass and damaged plastic shaft underneath. Replace with new shaft.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from AUSTIN, TX
- Parts Used:
- WB06X10712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Original part had melted because I forgot to put a container of water in microwave.
Son was able to remove the melted part and install the new one with no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from LAS VEGAS, NV
- Parts Used:
- WB02X11096
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked plastic where the spring attaches
A 2 yr old could do this snap out. Snap in less then. 30 seconds . What a shame and rip off on appliance repair shops - I called to do this rediculsley 40 second job and the wantvv$125.00!9t more. Omg. I’m a senior/ no wonder God punished the world wit Covid 19! Too many nasty infair. Buii I needed and rip offs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from LAFAYETTE, IN
- Parts Used:
- WB06X10712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stirrer fan cover was melted
This repai me couldn’t have been simpler! I noticed that the stirrer fan cover on our microwave had melted areas. My husband suggested we just buy a new microwave. As the handywoman of the family, I searched online to see if it was a fix that I could handle. I ordered a part for less than $20 and fixed it in about 30 seconds! All I had to do was pop out the plastic screw, put the fan in the new cover, and pop it back into place!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cassandra from ALDAN, PA
- Parts Used:
- WB24X10180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave wouldn't heat food
Took control panel off . Unplug plastic protector took off old put and put new one on... very easy and quick... same alot of money by doing it mtself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from CAPE CORAL, FL
- Parts Used:
- WB06X10712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic cover had quarter size hole burned
Use a butter knife to pop small plastic pin out and turn to remove. Used the metal pinwheel from old one and placed it back up in the microwave. Never heard of this being possible, but it seems to happen per the website and many other comments.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from MIDDLETOWN, NY
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lawn mower would not start
removed cover over motor blew it out of leaves and dust. Removes 4 screws and removed piece ordered. The coil was rusted and not connecting. Changed oiece its working again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from LONGWOOD, FL
- Parts Used:
- WB24X10180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Microwave with turn table and display present.
I followed the recommendations listed on the GE website for my model.
The cause of the fault was listed at 65% probable. I followed the suggestion, and yes it turned out the subject Interlock Door switch was my problem.
Working just fine now.
The cause of the fault was listed at 65% probable. I followed the suggestion, and yes it turned out the subject Interlock Door switch was my problem.
Working just fine now.
Was this instruction helpful to you?
Thank you for voting!