JNM1731DP1CC General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- CHARLES B. from CLARKSVILLE, TN
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Smelling and smoking. Than stop.
I took the cabinet off and saw where the switch had been burnt. So I remove it and order another one from your company. And I put new clips on it with heat shrinks. We might get another 30 years out it, Although I'm 80 years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from HOME, PA
- Parts Used:
- WB36X10071, WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Light in Microwave burnd out glas broken over lights
Replaced glass in frame and replaced lights
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from GILBERTSVILLE, PA
- Parts Used:
- WB36X10071
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass light lens cover was cracked
I first read the previously posted directions from other customers that were sent with my part order confirmation, which were all very helpful. Then, I basically used a screw driver to unscrew the screw holding the lens cover in place - be careful as it is a very tiny screw and it can easily fall behind your oven. You might want to place a large piece of cardboard over the space between oven and wall, as I did, so that you don't lose the screw in case it falls. Next I pried open the prongs, carefully slid out the cracked lens, and slid the new lens in place, pushed back the prongs and put the screw back in. I found that it was easier to use my fingers to first place and tighten the screw because it is very small and will keep falling out of place if you try to just use the screwdriver. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from TRINITY, TX
- Parts Used:
- WB06X10824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
my rack holder melted inside the microwave
I just inserted the new holder inside the opening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from MAYSVILLE, GA
- Parts Used:
- WB24X830
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would run but not heat
Removed the control panel, one screw at the top. Removed 2 screws on the door switch holder and removed the door switch. VERY EASY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Ludington, MI
- Parts Used:
- WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb broke in light socket
Tyring to get bulb out i ruined the light socket. Unscrewed the bottom cover of microware. Took out screw holding light socket, removed wires to socket with pliers, intsalled new socket. It was a piece of cake and the part was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Waterford, WI
- Parts Used:
- WB08X10016
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Burned out bulb
Screwed in new bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Council Bluffs, IA
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The bulbs burned out, the glass lens cracked and the light socket broke when trying to remove the bulb
Replaced the sockets, lens and bulbs. The first time the new bulb was touching the lens and the heat broke the lens and burnt out the bulb. The second time I adjusted the socket so that the bulb does not touch the lens.
Impressed by how quickly the parts arrived after the order was submitted. Two days.
Thank you.
Impressed by how quickly the parts arrived after the order was submitted. Two days.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Marina Del Rey, CA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb wouldn't light.
Removed difuser (one screw), removed old bulb, screwed in new bulb, replaced difuser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon F. from Brookline, MA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right hand surface lamp burned out. It apparently fald up and broke the glass cover. I wne on line when I found out the only local deaaler was some miles away and more expensive.
Simple. The parts came instantly. The glass was too big so I had it cut to size. I unscrewed the fixture with a screw driver replaced the bulb and slipped the glass cover into the frame and screwed the whole assembly in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Justice, IL
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb burned out -cracked holder lamp
pluged wires back on ,placed lamp holder and bulb back and replaced screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Marana, AZ
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken light lense
Removed one screw, installed new lense in lense frame, rescrewed. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Warren, MI
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken lens.
Used a phillips head screw driver and loosened the lens frame under the microwave. Removed the broken lens and replaced it with the lens ordered. Put the lens frame back in place and secured it with the phillips head screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois Jane from Fernley, NV
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light bulb burned out
took out several screws dropped down the panel under the microwave and unscrewed the bulb and put the new one in. It was a simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Shawnee, OK
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
time would count down but unit would not run & heat.
remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
Was this instruction helpful to you?
Thank you for voting!