JVM1540SM4SS General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ransford from LAUREL, MD
- Parts Used:
- WB26X10240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Turntable not rotating
Replaced the dead motor with new motor . I used YouTube video to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stella from BRADENTON, FL
- Parts Used:
- WB06X10712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burn hole in cover
My Son -in- law did it, removed the pivot pin removed the Cover and fan blade by turning it counter clockwise , Then replaced fan blade and cover and turning it clockwise and replaced the pivot pin .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karina from RIDGEFIELD, CT
- Parts Used:
- WB24X10181, WB24X10180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave was not heating and not turning.
I unplugged the appliance first. It was an over the range microwave so I only opened the front part where the buttons are, and behind it there’s a set of 3 door switches, carefully took out the burned down one and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Hyannis, MA
- Parts Used:
- WB26X10240
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Turn table did not rotate
Removed the original synchronous motor and replaced it with a new one. It turned on and rotated for about 1 day and stopped. I tested the motor for continuity and it was good. I need help in further trouble shooting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from DENVER, CO
- Parts Used:
- WB06X10704
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plate wasn't spinning.
Simply popped the turntable shaft in. It was installed by hand, no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from ROSSFORD, OH
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Cooking Tray
Placed the new tray into the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Discovery Bay, CA
- Parts Used:
- WB06X10359
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
purchased a home that the microwave needed a grease filter
Used Google to locate parts dealers for GE.
Ordered from Partselect.
Part arrived a few days later and I easily put it in.
I thought the cost of this part was out of line but all others sold it for about the same.
Ordered from Partselect.
Part arrived a few days later and I easily put it in.
I thought the cost of this part was out of line but all others sold it for about the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from HORN LAKE, MS
- Parts Used:
- WB26X10240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The turntable motor was dead
For this under cabinet wall mounted unit you will need two people to remove it. There are two mounting screws inside the bottom of cabinet. Remove the two screws and lower the cabinet. Place it on a flat surface and remove the 8 screws
From the bottom of the cabinet. Then remove the two screws from turntable motor. Reverse the procesdure and the job done. Don’t forget to turn off power. Good luck!
From the bottom of the cabinet. Then remove the two screws from turntable motor. Reverse the procesdure and the job done. Don’t forget to turn off power. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from LONGWOOD, FL
- Parts Used:
- WB24X10180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Microwave with turn table and display present.
I followed the recommendations listed on the GE website for my model.
The cause of the fault was listed at 65% probable. I followed the suggestion, and yes it turned out the subject Interlock Door switch was my problem.
Working just fine now.
The cause of the fault was listed at 65% probable. I followed the suggestion, and yes it turned out the subject Interlock Door switch was my problem.
Working just fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ira from LIVINGSTON, LA
- Parts Used:
- WB27X35382
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Food wouldn't heat up
Googled problem, removed diode, checked with meter and it was open, ordered new diode, checked new diode and it read open, installed. Any way, it didn't work. Went and bought new microwave!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from DENTON, TX
- Parts Used:
- WB02X21661, WB24X10180
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
No heat
Also installed capacitor diode cable from first parts order. Used Phillips screwdriver to remove parts and reinstall. The original latch board becomes unusable when removing parts requiring the purchase of a new board. New parts did not solve the problem so it was a waste of time and money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darin from SAN DIEGO, CA
- Parts Used:
- WB27X35382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No heat. No unusual noise. Appers to function other than no heat
Multimeter checked/confirmed switches, sensors, and fuse first. All good. High power diode was bad - Replaced. Still no heat but now loud "MMMMM" noise when running. This means either the capacitor is also bad and/or magnetron.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessie from PLAQUEMINE, LA
- Parts Used:
- WB06X10712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fan cover was melted with holes.
Simple fix. Prayed old off with flathead screwdriver. Installed new in less than 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from AUSTIN, TX
- Parts Used:
- WB06X10712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Original part had melted because I forgot to put a container of water in microwave.
Son was able to remove the melted part and install the new one with no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from LAS VEGAS, NV
- Parts Used:
- WB02X11096
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked plastic where the spring attaches
A 2 yr old could do this snap out. Snap in less then. 30 seconds . What a shame and rip off on appliance repair shops - I called to do this rediculsley 40 second job and the wantvv$125.00!9t more. Omg. I’m a senior/ no wonder God punished the world wit Covid 19! Too many nasty infair. Buii I needed and rip offs.
Was this instruction helpful to you?
Thank you for voting!