JVM2052DN2BB General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeffrey from FULSHEAR, TX
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
M/W would not start. control panel OK
unplugged power
removed main black cover.
located part WB24X10047 and replaced
removed main black cover.
located part WB24X10047 and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pearlie from Beulaville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Timer, light and control pad worked. Turn table and heat did not work. Oven would not start up.
I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followed them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ira from LIVINGSTON, LA
- Parts Used:
- WB27X35382
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Food wouldn't heat up
Googled problem, removed diode, checked with meter and it was open, ordered new diode, checked new diode and it read open, installed. Any way, it didn't work. Went and bought new microwave!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from BLUFFTON, SC
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
The unit would run when the door was open!
First I had to accept the fact that the unit was designed to keep non-professional people from doing any repairs. The switch was installed in such a manner that I had to break the mounting to remove the switch, then drill a hole in the mounting to secure the new switch in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kip from POWELL, OH
- Parts Used:
- WB27X10928
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Not heat
-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andrew from HOMOSASSA, FL
- Parts Used:
- WB56X35363
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
installed new kitchen cabinets
the problem was the mounting bracket that was installed when the house was built ,was not the bracket that came with the microwave. It was used to step the microwave out 3" in front of the other cabinets for the style that they were using then. so when I was installing the new cabinets I didn't want that style, so I ordered the original mounting bracket. It was a perfect fit and the install went great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G. Wayne from GARDNERVILLE, NV
- Parts Used:
- WB21X10148
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
To heat a cup of coffee, user entered "10:00" instead of "1:00". Mess! After cleanup, microwave ran, but would not heat. While running, it made 2 or 3 time the noise volume as before.
I went for the cheap things first. Ohmmeter showed one of the thermostats in the magnetron compartment was open. I ordered and replaced all three thermostats. Still no heat. I took the unit off the wall (aaarrgh!) and checked the oven cavity thermal cutout. It said 7 ohms. I tested by shorting the wires together, but still no heat. So, I ordered the magnetron and diode cable. When replacing the diode cable (be sure to discharge the big cap!) either I broke it, or it was already damaged. It came off in two pieces. The new diode cable was re-enforced with thick heat shrink tubing, to prevent such breaking. You need a very short screwdriver to replace the magnetron. Now, all fixed! ~$150. A new one lists for $2000, installed in the overhead. My wife thinks I am a genius.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mack from Jacksonville, FL
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
No heat.
Replaced the fuse. Result; did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from New York, NY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat
Replace the fuses
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Sioux Falls, SD
- Parts Used:
- WB06X10564
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken turntable coupler
Remove and installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from New Philidelphia, OH
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave would turn on ,BUT turn table would not turn and oven would not heat.
Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Fairview, TX
- Parts Used:
- WB02X35607
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dirty charcoal filter
Open vent, removed old filter, inserted new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from San Carlos, CA
- Parts Used:
- WB06X10564
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turntable not turning
The hard part I thought, was to find the part I needed. Not so with Part Select. It took less than a minute to find and order. The new part showed up in a few days. I noticed the new part was a little differant in a good way. The socket porition was a little deeper making it a little better. The microwave works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Louisville, KY
- Parts Used:
- WB36X10328
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lights were burned
It was REALLY EASY finding the right parts using your diagrams..Thanks for your HELP!!I will definitely be back.Dan H
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kernersville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!