JNM1541DM5BB General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patricia from Tarpon Springs, FL
- Parts Used:
- WB36X10328
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior lamp burned out
Unscrewed the vent at top of microwave exposing small access to bulb. The access to this was very limited so that was the major issue in changing the bulb. You needed small hands to do the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Carrollton, TX
- Parts Used:
- WB56X10669
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Installing New Microwave
Required removing the old unit and disconnecting the exhaust ductwork and drilling new holes for attachment to the cabinet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from STRONGSVILLE, OH
- Parts Used:
- WB24X10180
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bad interlock switch
Took off vent cover and front panel, replaced switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juli from Melbourne, FL
- Parts Used:
- WB06X10712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Melted hole in plate
Remove pin and shift old cover plate clockwise to release cover. Remove and insert fan into new cover and replace cover by inserting cover plate tabs and turning counter clockwise. Insert new pin to connect new cover plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from NAVARRE, FL
- Parts Used:
- WB06X10712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stirrer fan cover had hole melted in it.
Gently remove plastic rivet holding cover in place.Rotate cover slightly and pull down. Remove stirrer fan from old cover and place on new cover. Place cover back in microwave and rotate till rivet hole lines up and replace rivet. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patty from SEATTLE, WA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the glass circular tray inside had cracked in half.It was of no use. I reordered another
The tray came within 5 days and I simply took it out of its well-packaged box and slipped it into my microwave. It is working just like new. I can't thank you all for being so punctual and reliable. better than having to buy a brand new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RogerPotter from JACKSONVILLE, FL
- Parts Used:
- WB15X24435
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom of Handle Broke
Open the microwave door. On the outer edge the is a 1 inch thick black mold that goes around the entire door. Pry that back with a flat head screwdriver where the handle is and you will see the 2 phillip screws are exposed, top and bottom. Remove them..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debora from Saugus, MA
- Parts Used:
- WB06X10359
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Too dirty to clean, bought new parts.
I had already removed the old grease filters. Unwrapped the new grease filters and popped into place. No tools were necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ransford from LAUREL, MD
- Parts Used:
- WB26X10240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Turntable not rotating
Replaced the dead motor with new motor . I used YouTube video to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karina from RIDGEFIELD, CT
- Parts Used:
- WB24X10181, WB24X10180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave was not heating and not turning.
I unplugged the appliance first. It was an over the range microwave so I only opened the front part where the buttons are, and behind it there’s a set of 3 door switches, carefully took out the burned down one and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from SOUTHSIDE, AL
- Parts Used:
- WB06X10712, WB01X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The fan cover in the top of the microwave had a melted spot.
I used a flat screwdriver blade to push out the rivet. Then used the screwdriver to loosen the fan cover and gave it a little twist. It came out with no problem. There was some grease build up on the aluminum fan, so I cleaned it. I placed the clean fan into the new fan cover and put it back in place in the microwave. There are several notches to match up, and then I gave it a slight twist to secure the notches. Then, the new rivet was put into the hole and pushed to make it secure. Finished!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from LAUREL, MD
- Parts Used:
- WB07X11009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Grill vent broke
Fairly easy to repair. The hardest part for me was trying to get the lip under the frame so it will snap in.
I could only replace the left screw because the right didn’t align properly. The grill fits tightly so I’m not worried about the one side.
I could only replace the left screw because the right didn’t align properly. The grill fits tightly so I’m not worried about the one side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecil from Asheville, NC
- Parts Used:
- WB24X10180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave quit working
Removed top bar and control panel. Checked fuse with multimeter-it was fine. Checked bottom two door latches with multimeter-fine. Went to check top latch and discovered that the spring loaded “button” which is depressed by the door extension had lost its springiness. Ordered new one. Replaced it. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from DENVER, CO
- Parts Used:
- WB06X10704
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plate wasn't spinning.
Simply popped the turntable shaft in. It was installed by hand, no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Hyannis, MA
- Parts Used:
- WB26X10240
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Turn table did not rotate
Removed the original synchronous motor and replaced it with a new one. It turned on and rotated for about 1 day and stopped. I tested the motor for continuity and it was good. I need help in further trouble shooting.
Was this instruction helpful to you?
Thank you for voting!