JNM1541DM4BB General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Deborah from SOUTHSIDE, AL
- Parts Used:
- WB06X10712, WB01X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The fan cover in the top of the microwave had a melted spot.
I used a flat screwdriver blade to push out the rivet. Then used the screwdriver to loosen the fan cover and gave it a little twist. It came out with no problem. There was some grease build up on the aluminum fan, so I cleaned it. I placed the clean fan into the new fan cover and put it back in place in the microwave. There are several notches to match up, and then I gave it a slight twist to secure the notches. Then, the new rivet was put into the hole and pushed to make it secure. Finished!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from LAUREL, MD
- Parts Used:
- WB07X11009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Grill vent broke
Fairly easy to repair. The hardest part for me was trying to get the lip under the frame so it will snap in.
I could only replace the left screw because the right didn’t align properly. The grill fits tightly so I’m not worried about the one side.
I could only replace the left screw because the right didn’t align properly. The grill fits tightly so I’m not worried about the one side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecil from Asheville, NC
- Parts Used:
- WB24X10180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave quit working
Removed top bar and control panel. Checked fuse with multimeter-it was fine. Checked bottom two door latches with multimeter-fine. Went to check top latch and discovered that the spring loaded “button” which is depressed by the door extension had lost its springiness. Ordered new one. Replaced it. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Hyannis, MA
- Parts Used:
- WB26X10240
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Turn table did not rotate
Removed the original synchronous motor and replaced it with a new one. It turned on and rotated for about 1 day and stopped. I tested the motor for continuity and it was good. I need help in further trouble shooting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stella from BRADENTON, FL
- Parts Used:
- WB06X10712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burn hole in cover
My Son -in- law did it, removed the pivot pin removed the Cover and fan blade by turning it counter clockwise , Then replaced fan blade and cover and turning it clockwise and replaced the pivot pin .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delores from Portland, OR
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Glass tray somehow got a nick in the edge, a few days later it split while in use.
Another company said the new plate would arrive in mid-March, this company seemed to be faster so ordered the tray here, and it came in less than a week. I put the turn button back in the center hole, set the wheeled ring on the bottom of the oven, fitted the new glass tray onto the turn button.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from ROSSFORD, OH
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Cooking Tray
Placed the new tray into the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Allentown, PA
- Parts Used:
- WB07X11008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The control panel shorted out.
Popped off the control panel. Unscrewed and disconnected the circuit board. Reconnected and screwed in the new panel and popped it back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Discovery Bay, CA
- Parts Used:
- WB06X10359
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
purchased a home that the microwave needed a grease filter
Used Google to locate parts dealers for GE.
Ordered from Partselect.
Part arrived a few days later and I easily put it in.
I thought the cost of this part was out of line but all others sold it for about the same.
Ordered from Partselect.
Part arrived a few days later and I easily put it in.
I thought the cost of this part was out of line but all others sold it for about the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from MEDFORD, NY
- Parts Used:
- WB06X10704
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass Turntable not rotating when microwave oven ON
Turntable shaft was worn and out of shape likely due to heat. Simply remove rotating glass and damaged plastic shaft underneath. Replace with new shaft.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from AUSTIN, TX
- Parts Used:
- WB06X10712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Original part had melted because I forgot to put a container of water in microwave.
Son was able to remove the melted part and install the new one with no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from LAFAYETTE, IN
- Parts Used:
- WB06X10712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stirrer fan cover was melted
This repai me couldn’t have been simpler! I noticed that the stirrer fan cover on our microwave had melted areas. My husband suggested we just buy a new microwave. As the handywoman of the family, I searched online to see if it was a fix that I could handle. I ordered a part for less than $20 and fixed it in about 30 seconds! All I had to do was pop out the plastic screw, put the fan in the new cover, and pop it back into place!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cassandra from ALDAN, PA
- Parts Used:
- WB24X10180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave wouldn't heat food
Took control panel off . Unplug plastic protector took off old put and put new one on... very easy and quick... same alot of money by doing it mtself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from LONGWOOD, FL
- Parts Used:
- WB24X10180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Microwave with turn table and display present.
I followed the recommendations listed on the GE website for my model.
The cause of the fault was listed at 65% probable. I followed the suggestion, and yes it turned out the subject Interlock Door switch was my problem.
Working just fine now.
The cause of the fault was listed at 65% probable. I followed the suggestion, and yes it turned out the subject Interlock Door switch was my problem.
Working just fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from HORN LAKE, MS
- Parts Used:
- WB26X10240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The turntable motor was dead
For this under cabinet wall mounted unit you will need two people to remove it. There are two mounting screws inside the bottom of cabinet. Remove the two screws and lower the cabinet. Place it on a flat surface and remove the 8 screws
From the bottom of the cabinet. Then remove the two screws from turntable motor. Reverse the procesdure and the job done. Don’t forget to turn off power. Good luck!
From the bottom of the cabinet. Then remove the two screws from turntable motor. Reverse the procesdure and the job done. Don’t forget to turn off power. Good luck!
Was this instruction helpful to you?
Thank you for voting!