JES2150MR1SA General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from Indianapolis, IN
- Parts Used:
- WB49X10108, WB02X10895
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
brokencooking dish
easy to handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David W. from Dover, OH
- Parts Used:
- WB02X10895
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The little wheels keap coming off.
R & R - Remove old part,cleaned roller grove,Replaced old part with new one.Job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marshall from CRESTWOOD, KY
- Parts Used:
- WB02X10895
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken plastic wheel (Roller) on the turntable plate support roller guide.
Open the shipping package the new roller guide comes in and removed it from the package. Open the microwave door and removed the glass turntable plate. Remove the broken roller guide ring and roller wheel/s. Clean the surface that the roller guide assembly rides on. Place the new roller guide assembly into the microwave. Clean the bottom surface of the glass turntable plate that the roller guide wheels ride on and put the plate back into the oven. Place a cup of water onto the turntable plate close the oven door and start the microwave. Looking through the door assure that the new roller guide assembly is rolling smoothly under the turntable plate. Stop the oven, remove the cup, reset the oven timer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from CINCINNATI, OH
- Parts Used:
- WB02X10895
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Replace the circle that makes tray turn
I felt proud of myself for just taking time to get serial # ,call verify on serial # to match picture on internet.,which #did not match part, so I question, a re check ;thank goodness I did as the part would have been to large, so glad I ask question before mailing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josh from ENGLEWOOD, CO
- Parts Used:
- WB49X10108
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Closure assembly bent and slide wheel broke
The key to this repair is attaching the spring once the rest of the assembly is attached. I primarily used a wratcheting screw drive to remove the assembly but used a socket attachment with the screw bit to finish it off.
First, I removed the spring entirely. In order to attach the spring, I expanded the spring by sliding quarters into each of the coils (I had a quarter in every coil in order to get the ends as close as possible). I then first attached the spring to the post on the right side. I would have preferred to attach it to the closure assembly arm as the angle to attach was much simpler with the spring detached however there wasnt enough room to work around the post.
I then adjusted the closure assembly arm to be aligned with the spring and with a little elbow grease, stretched the string the remaining 1/2" or so and connected it to the arm. Once connected, I opened the fridge door and was easily able to remove the quarters.
First, I removed the spring entirely. In order to attach the spring, I expanded the spring by sliding quarters into each of the coils (I had a quarter in every coil in order to get the ends as close as possible). I then first attached the spring to the post on the right side. I would have preferred to attach it to the closure assembly arm as the angle to attach was much simpler with the spring detached however there wasnt enough room to work around the post.
I then adjusted the closure assembly arm to be aligned with the spring and with a little elbow grease, stretched the string the remaining 1/2" or so and connected it to the arm. Once connected, I opened the fridge door and was easily able to remove the quarters.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from OMAHA, NE
- Parts Used:
- WB02X10895
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Our original roller guide had a broken section which controlled the circular movement
We removed the glass circular plate of the microwave. We replaced the original roller guide with the new part. Then we placed the glass plate back in its place. Quick and simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earnest from WINCHESTER, CA
- Parts Used:
- WB02X10895
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
1 of 3 roller wheels came off
Removed old roller assembly and installed new roller assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from RALEIGH, NC
- Parts Used:
- WB49X10108
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I needed a new glass hot plate for a cracked plate that came with the original microwave.
I placed the new hot plate in the old microwave. It worked perfectly, and no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Laurel, NY
- Parts Used:
- WB49X10108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass cooking tray broken
Simply replaaced broken cooking tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Warner Robins, GA
- Parts Used:
- WB49X10108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass tray
just placed it on the wheel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from New Orleans, LA
- Parts Used:
- WB02X10895
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problems
Remove the Glass rotating tray and replace the guide
Was this instruction helpful to you?
Thank you for voting!