HVM1750DM2CC General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donald from Raleigh, NC
- Parts Used:
- WB06X10420
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable motor burnt out
lowered bottom panel, unpluged turntable motor, unscrewed one screw. replaced old motor with new alinged turntable button. repluged motor wire and finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from TREASURE IS, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Under the microwave there are two light bulbs that light up the top of the oven/range.
Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from MAYSVILLE, GA
- Parts Used:
- WB24X830
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would run but not heat
Removed the control panel, one screw at the top. Removed 2 screws on the door switch holder and removed the door switch. VERY EASY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tommy from Santa clarita, CA
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Previoous glass lens was broken
This repair was easy and could be done by anyone. If you undertake to do this replacement, remember to slowly bend the medal tabs back that hold the lens. Handled roughly these tabs could break off.
This repair can be don in under 5 minutes, easily !!
This repair can be don in under 5 minutes, easily !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from UNIVERSITY PA, MD
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb burned out light that is under the microwave, which lights the oven below.
thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Ludington, MI
- Parts Used:
- WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb broke in light socket
Tyring to get bulb out i ruined the light socket. Unscrewed the bottom cover of microware. Took out screw holding light socket, removed wires to socket with pliers, intsalled new socket. It was a piece of cake and the part was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from HOME, PA
- Parts Used:
- WB36X10071, WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Light in Microwave burnd out glas broken over lights
Replaced glass in frame and replaced lights
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Council Bluffs, IA
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The bulbs burned out, the glass lens cracked and the light socket broke when trying to remove the bulb
Replaced the sockets, lens and bulbs. The first time the new bulb was touching the lens and the heat broke the lens and burnt out the bulb. The second time I adjusted the socket so that the bulb does not touch the lens.
Impressed by how quickly the parts arrived after the order was submitted. Two days.
Thank you.
Impressed by how quickly the parts arrived after the order was submitted. Two days.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Waterford, WI
- Parts Used:
- WB08X10016
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Burned out bulb
Screwed in new bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Marana, AZ
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken light lense
Removed one screw, installed new lense in lense frame, rescrewed. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Watertown, WI
- Parts Used:
- WB06X10420
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The coupler shaft broke.
When you put a rectangular pan on the turntable in the microwave, the tumbler coupler stops and the steel shaft on the motor keeps going and brakes the plastic shaft on the coupler. The fix, 5 screws on the bottom of the microwave drop the cover. One screw on the motor, drops the motor, just to see the problem. Disconnect power to the motor temporarily. You really don't need to take the motor out if you know how the coupler fits on the motor shaft. Put the motor back and drop in a new coupler from inside the micro, and it is done. Put the cover back on and you are set to go. Then don't put a non-rotating pan on a rotating turntable. A $5 part and $7 shipping is a lot better than a new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CARL from CAMBRIDGE CITY, IN
- Parts Used:
- WB06X10420
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken turntable coupler
Pulled off old coupler.It was tight so used a trim bar to remove. Checked motor shaft since there was 2 types available.One, square shaft,other D shaft. Ordered in AM and received the next day in PM by Fedex.. Can`t get much better than that! Pushed on and done......Like new again...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Justice, IL
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb burned out -cracked holder lamp
pluged wires back on ,placed lamp holder and bulb back and replaced screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Marina Del Rey, CA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb wouldn't light.
Removed difuser (one screw), removed old bulb, screwed in new bulb, replaced difuser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon F. from Brookline, MA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right hand surface lamp burned out. It apparently fald up and broke the glass cover. I wne on line when I found out the only local deaaler was some miles away and more expensive.
Simple. The parts came instantly. The glass was too big so I had it cut to size. I unscrewed the fixture with a screw driver replaced the bulb and slipped the glass cover into the frame and screwed the whole assembly in.
Was this instruction helpful to you?
Thank you for voting!