JES1384SF08 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- CHARLES from LAKE ARIEL, PA
- Parts Used:
- WB27X10568
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave oven was completely dead.
Continuity checks showed the flame sensor was open. Schematic notes it opens at 217 degrees and closes at 30 degrees. Removed sensor and placed in freezer for twenty minutes. Tested sensor and it was now closed, reinstalled and microwave worked normally. Ordered new sensor in case the original is operating at too low a temperature.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Astoria, NY
- Parts Used:
- WB27X10568
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The display was off and no buttons were working
I took the cover off and followed the electric current to see if it got as far as the display.
I did not get past the thermostat shut off where the current stoped. I jumped the thermostat and the unit worked. The part was so inexpensive that I decided to replace it rather than try and freeze the old one in hopes of "reseting" it.
I did not get past the thermostat shut off where the current stoped. I jumped the thermostat and the unit worked. The part was so inexpensive that I decided to replace it rather than try and freeze the old one in hopes of "reseting" it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chester from Port Orchard, WA
- Parts Used:
- WB39X82
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rotating glass tray broken.
A fragile glass tray providing a rotating surface for the microwave required replacement. The tray arrived scrupulously packaged to insure contents production. Unpacking was simply accomplished and installation achieved without undue effort. Thank you for prompt delivery and consideration for the attention paid to my purchase.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from KETTLE FALLS, WA
- Parts Used:
- WB24X10103
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Trip breaker when opening door
Door microswith was stuck on. This is caused, I discovered, by frequently stopping the oven, while running, by opening the door rather than using the stop button. Causes the switch to arc and eventually fail. This causes the safety microswitch to trip the breaker when door is opened. There are little nubs sticking up on the spade connectors. You must squeeze them down before you can remove them from the switch. The main door switch is the upper one, mounted at an angle. You have to remove the latch assembly to remove the switch. The problem was obvious once I got the switch out. This problem could also blow the fuse, but in my case the breaker tripped first. Use an ohmmeter to check switch and fuse. The door switch is normally open. The safety switch is normally CLOSED. Instructions inside were helpful and described this problem. So, avoid this repair by always stopping oven with stop button!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jorge from miami, FL
- Parts Used:
- WB27X10568
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no power, front panel off
removed cover and tested fuse, fuse ok, check flame switch (thermostat) bypassed it with thin wire ,all power on!!...ordered it, got it, replace it within 5 min, as soon as part arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William R from Chicago, IL
- Parts Used:
- WB27X10568
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Everything dead--display, oven, all. Someone had turned on the onven woth nothing in it, set on HI for fifteen minutes .
Traced out 120volts from neutral to hot though fuse, and "high limit" switch screweed to far side of oven exterior cavity. High limit thermostat was "open". Jumped it out to see if unit would produce heat. Melted 1/2 cup of ice in thirty seconds. Ordered new part. Later foud out hi limit can be "re-set" by subjecting it to sub-freezing temperatiures. This is true, but I installed new part just to be safe. Machine is working fine now and has been in daily srvice for over two weeks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Medford, NY
- Parts Used:
- WB27X10568
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The microwave would not turn on - no clock or power
It pays to troubleshoot a broken appliance before thinking about buying a new one. I removed the cover and found the manufacturer's circuit and troubleshooting diagrams inside. The fuse was good, next in line was the flame sensor. Meter showed it was open, so I knew that was it. Disconnect the wires and screw, replace part, replace cover. DONE! I knew I had the right part from the pictures on PartSelect's web site. Total cost under $20 compared to ten times that for a new one. Had the part in two days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from San Diego, CA
- Parts Used:
- WB39X82
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke glass cooking tray
I called partselect after looking at their web site to confirm that I was ordering the right part. They were very helpful. Partselect prices were lower than competitors even after shipping. The part came the very next day. I was pleasently surprised how quick and efficient they were. Thank you partselect for your assistance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rex from Burleson, TX
- Parts Used:
- WB39X82
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken cooking tray replacement
The repair was simple. replace the broken tray with the new one.....Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from VI0LET, LA
- Parts Used:
- WB39X82
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass Broke
Put it right in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- raul from elmhurst, NY
- Parts Used:
- WB39X82
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Cooking Tray
Open the microwave tray, set the class cooking tray on the rotating device an done. Real peace of cake. Thank you for the promp delivery. Your future costumer, raul.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hilda from marysville, WA
- Parts Used:
- WB39X82
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I accidently broke my cooking tray.
I ordered a new one in about 3 days it was here. all I did is put it in. Thanks so much. I have all whirlpool appliances and am happy I have a place to order when I need a part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Buffalo, NY
- Parts Used:
- WB39X82
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
blew up glass plate over heating/burning sugary food
cleaned out vents, inside of microwave, replaced plate
Plate replacement took only a few days Very fast delivery Thanks
Plate replacement took only a few days Very fast delivery Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose j from SYLMAR, CA
- Parts Used:
- WB49X10080
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
wave guide cover
Remove two plastic buttons,remove old damaged cover,replace with new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from POTOMAC, MD
- Parts Used:
- WB27X10567
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Power cut off to Microwave - It was run empty
1. Remove trim kit - Philips head screw driver
2. Remove Microwave from the wall - Philips head screw driver
3. Remove outer microwave cover - required tamper proof torx bit drivers
4. Replace Magnetron thermostat. On this model there are 2. in this case it was on top of the unit tied into the wiring harness to the main panel.
5. Reinstall microwave and trim kit
2. Remove Microwave from the wall - Philips head screw driver
3. Remove outer microwave cover - required tamper proof torx bit drivers
4. Replace Magnetron thermostat. On this model there are 2. in this case it was on top of the unit tied into the wiring harness to the main panel.
5. Reinstall microwave and trim kit
Was this instruction helpful to you?
Thank you for voting!