HVM1540SP1SS General Electric Microwave - Instructions

so easy, but how do i turn light off?

Part recieved next day. thanks so much

Since the job required replacing both the bulbs and sockets the unit was dropped from the wall. Used a towel and plywood to protect the range under the unit. Then these steps: Unplugged the power cable and placed a support board under the unit while removing three bolts from overhead cabinet. Next, removed support board and with a helper rotated the unit down and lifted it out of the rear wall mounting panel. Then turned the unit upside down, removed the bottom plate and unplugged the feed wires and two wires to each of the sockets. Next the single screws holding the sockets were removed and the sockets extracted from the mounting shells and new units were installed. When remounting the unit it was necessary to start all three bolts from the upper cabinet just a few turns and then tighten the center bolt completely first.

My son=law did repair because I am elderly and it was necesary to remove the bottom plate of the microwave which I was unable to do. The microwave was installed in 1987 and I believe this was the first time to replace the bulbs. When my son removed them the bulb was diintergrated. That's how old they were. Once he was able to remove the underneath plate the repair was easy except for removing the old bulbs. I think that I could have done it myself but he was available and I am sure it was done much better. All in all the parts)bulbs) were correct and everything is workiin fine. This is a good place to order replacement parts. In fact I am going to order a new charcoal filter. He took the label off the old one and I am ordering the replacement. After all 1987 may have been a good year, but time for a new one. Mary

Install your item works well. Will use you for other items,

removed the lens cover with one screw and replaced bulb

remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.

Replaced light socket and bulb. Real easy repair.

replace socket

Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.

Unplug appliance, Staring from the rear sides, remove the four side screws. Remove the left and right front screws and finally the front center screw. The bottom panel hinges down toward the rear . Unplug the input wires from the sockets . Unscrew the two retainer screws (one each) and pull the sockets out of the panel. Note that the retainer screws are shouldered. The shoulder fits through the elongated slot in the socket. Screw the bulb into the socket and insert through the mounting hole. Insert and tighten the mounting screws. Note that the sockets may appear to be a bit loose. That's OK because of the shouldered screw. Don't over tighten or you risk stripping the threads of the panel. Plug in the input sockets and install the panel screws in the reverse order of removal. Plug the appliance in and test the bulbs.

Opened the microwave oven door, unscrewed two screws which held the control panel on, then I removed two of the door switches (each had two screws), and then used the continuity tester to see which one was not operating. It turned out to be the secondary door switch, replaced it and to my amazement, the microwave worked. I have never repaired an appliance before but I didn't want to replace our over-the-stove built in microwave. It was the best day ever when it was working again! The hardest part was getting myself to try the repair.

Loosen the two long anchor bolts that screw into the top of the microwave cabinet. These are usually in a shelf or cabinet directly above the microwave. Tilt the microwave forward enough to remove the 2 Phillips head screws from the top of the microwave cabinet. They are near the front. When these two screws are out, remove the fan vent. Once the fan vent is off, remove one screw that holds the control pad in place. Let it hang down. Just to the left of the control pad, you will see wires leading to three switches that close when the door is closed. Use a torx driver to remove the two screws that hold the switch bracket in place. With the bracket out, unplug the wire harnesses. On the opposite side of the wiring connected, a tab holds each switch in place. Lift the tab and slide the switches out. Usually, the bad switch will be identified by a loose or broken spring. Test them by pressing down on the switch. If you notice the bad switch spring, this is usually the bad one. When you have the new one, simply push it back into the appropriate slot and be sure that the holding tab snaps back in place. Plug the wires back in and re-attach the bracket. Put the control pad back on, then the fan vent. When down with those, push on the bottom of the microwave to lift it back into place and tighten the two anchor bolts in the top.

First, unplug microwave. Unscrew two screws at top of microwave, slide grill cover left and remove. This allows access to single screw holding control panel. Remove this screw and lift up control panel to remove. Secondary door switch is black switch at lowest position. The switch is held in place by a lever in back and very hard to get to. Remove the wires plugged into the switch, then remove two screws holding the plastic switch mount that holds all three switches. These screws use a "star" type screwdriver. Once the plastic mount is free, lift it up, right, and tip it slightly to find the lever that will release the black secondary door switch (the lowest switch)...release the broken switch, snap the new switch in its place. Replace the plastic mount by lifting and replacing back into position and replace the two "star" screws. Now, replace the wires onto the new switch, and test operation. Replace control panel, and top grill. It goes faster than it writes...getting the old switch out through that difficult to reach lever was the hardest part...still less than thirty minutes.

Followed suggestion by previous poster to remove bottom panel...facilitated process well

Very easy to replace the light socket. Unscrew screws under microwave to lower the base. remove screw at rear of light socket. Unplug power to socket. Plug wire into new socket. Replace new socket into base and replace serew. Hold base plate up to microwave and replace all screws. Do yourself a favor, if replacing one of the lights, go ahead and do both. Shipping cost is the same for 1 or 2 bulb sockets.