JVM1410BC001 General Electric Microwave - Instructions

I removed the screws that held the bottom in and then dropped it down to access the motor. I removed the 2 screws that held the motor in and unplugged it. I then plugged the new one in and reattached it with the 2 screws and put the bottom back on. It took me about 5 minutes to fix it for only $40.00.

Thanks to the person who previousley detailed how he drilled holes to access 2 hidden screws, that made my job so easy. Thank You.

Kept the microwave in place( it is above the stove) 1 unplug the microwave 2unscrew the cover plate on the bottom3unplug connections,light and drive motor.4 unscrew drive motor replace with new drive motor,reverse the remaining process. Part took about 3-4 days to deliver,plan accordingly.

Using a phillips screwdriver, remove 7 screws from the unerpanel of the Spacesaver Microwave. The panel will swing down from the rear edge hinge, exposing the lights and the stirrer motor. Remove the electrical connector and two screws holding the motor in place and remove the motor. The stirrer inside the oven can then be removed if desired. Install the new motor in reverse order. Note rotate the stirrer inside the oven to align the motor shaft to facilitate assembly.

Used chisel to remove inside cover. Unscrewed broken handle. (Didn’t expect that there was a second set of screws That were covered by metal frame of microwave. Had to cut the screw to remove. Then screwed the new handle back in. This handle only had 2 screws. Hope it holds as well as the 4 original screws. Part was kind of expensive, was not informed that there was an error in processing my shipment until I called. Then part showed up 2 days later.

-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order

Followed the video online.

Disconnect power to microwave. Remove plastic rotor attached to motor shaft. I had to pry up from underneath it with a screwdriver to break it loose. Cover surface below microwave as bottom cover screws are small and easily lost. Remove three front and two rear screws from bottom cover and it will swing down. Locate the drive motor on the cover, disconnect the power leads, remove one set screw and rotate the old motor off the cover. Reverse instructions to re-install new motor. Swing bottom cover back up and re-install the five small screws. I had a little trouble lining up the screw holes and it helped to use a finishing nail to align the holes in the cover with those in the microwave frame. Reinstall plastic rotor on motor shaft, reconnect power to microwave and test the turntable.

Removed old film, installed new horizontally and pulled it downward (match it along the top first). The cover required 2 "hooks" to be removed, only needed 4 clips. Used a screwdriver to remove the 2 clips.

I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followed them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.

I first went on you tube and typed in my brand and model number. It brought up how to take apart the door to get at the four screws. I used a butter knife to pop out the door frame. With the inner door off the first two screws came out then you can get at the other two screws. I used the same old screws to reinstall the new handle. The door handle arrived in two days via ups. The frame snaps together, very easy. Never installed a handle before. The price was right and the wife wanted this fixed, now!

Following the instructions from prior PartSelect folks for this part (thank you for great instructions), I removed the door from the microwave (first had to remove the fan vent grill above the door (2 Phillips screws), then I carefully removed the back plastic door frame using the thin puddy knife to carefully pop it off. Removed the first 2 screws on that are visible. Removed the inner door frame (was the most difficult part of the process to do without breaking the front panel frame) to expose the inner 2 screws. On our microwave, the front panel was also cracked, so I removed and replaced it (very simple), attached the new handle to the front panel with the inner screws (Phillips 2) and then popped the inner door back in, screwed in the last 2 screws and attached the back plastic door frame. Reattached the vent fan cover and the door. A bit more complicated than originally thought, but overall not bad. Charlie C

Straight forward repair. The item came quickly, and since I had taken the other motor out previously to test it, the instalation was a breeze. There are a total of 7 external screws for the cover and two internal that hold the motor in place. One screw driver is all you need and access to the bottom of the microwave (I was fortunate that mine was an above the range model so accessing the bottom was easy). Anyone with a little manual dexterity can handle this repair now problem!

First I unplugged microwave oven, then removed the six screws at the bottom of the microwave and lowered the base to expose the small motor. I removed the motor and replaced it with the new one. From inside the oven I pushed the drive shaft back into the new motor, then replaced the bottom with the six screws. I plugged the oven in and tested it. It worked! In less than 15 min. I saved over $220, and I'm a 65 year old Grandma! Thank you, thank you!

This is the 3rd time I have used PartSelect to help me repair appliances I never thought I could fix on my own. The troubleshooting knowledgebase walked me through repairing my dryer, the illustrated parts diagrams gave confidence to replace the thermostat in my oven, and now to replace the tray motor in my microwave, all saving lots of money in my pocket instead of the repairmans. This motor repair simply requires removal of 4 screws, and unplugging an electrical connector. Hooray for PartSelect!!!