JVM1870SK01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- robert from salmon, ID
- Parts Used:
- WB36X10071
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lens Was Not Sized To Fit And Was Left Extremely Sharp
Had to take to a local glass shop for sizing and to remove sharp edges. Will never order again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from RIVERSIDE, CA
- Parts Used:
- WB24X830
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Unit would run when door is opened
Two screws to remove upper from vent. Two screws to remove the didgit panel lift ip to remove and put aside remove the two screws that hold the door sensors. Depress the tab to remove the defective sensor disconnect the electrical connector and replace the new sensor snap it back into the holder install the two screws, install the didgital panel and vent panel to complete the job. Please be aware that there is a video of this procedure on Y tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marielen from newport, RI
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked Microwave Glass Plate
Odered replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Summerville, SC
- Parts Used:
- WB06X10521
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Microwave Rack Holders (Little plastic pieces) Broken
Found your site online, ordered parts needed. When parts arrived I just put them into the holes in the microwave and popped on the self. Worked like a charm! Thanks very much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from VAIL, AZ
- Parts Used:
- WB36X10213
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
needed light bulb
The halogen light bulb took a little skill. The prongs were a little difficult to maneuver into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kambiz from Mesa, AZ
- Parts Used:
- WB02X10733
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Charcoil Filter needed to be changed.
GE microwave displayed the message that Charcoil Filter needs to be changed. I disconnected the unit and removed the top two screws then removed the top panel by sliding it gently to the left. Replaced the filter. And positioned it in the same way the old filter was installed. Replaced the top panel and screws, Connected the unit back and used the Menu option to reset the Charcoil Filter warning option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Desert Hot Springs, CA
- Parts Used:
- WB07X10476
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace Vent Grille Assembly
Old one broke. Looked into the internet. Found PartsSelect.com. Called the 800 number. Lady helped to make sure I bought the entire assembly assembled. Order that day, received in about 4/5 days. installed. Threw away old one. Very happy with the service and the ease of ordering/installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Edison, NJ
- Parts Used:
- WB06X10521
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
2 rack holders broke
used the Dremel Osciilating tool with small blade to quickly cut/remove the old rack holder and then inserted new hold. Took less then 5 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from POWAY, CA
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Previous coupler was cracked/broken
I ordered and replaced the coupler. Once installed, all was well!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ina from Horn Lake, MS
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Motor went out. Glass tray wouldn't rotate any longer
Removed the 6 screws that held the cover below my microwave. Unplugged the part, plugged in the new one and I was done. My part arrived from you just one day after I ordered it! It was my first microwave repair ever, and it couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Friendship, MD
- Parts Used:
- WB02X10733
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Needed to change filter
Remove two screws on the top of the grill. Slide the grill to the left and then pull straight off. Slide the filter in place. Replace grill and screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LEN from OCEAN SPRINGS, MS
- Parts Used:
- WB26X10038, WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Loud noise from the Microwave and the tray was not truning
I followed the directions on your web site. I removed the screws adn dropped the bottom tray, unplugged the drive motor, removed two screw, and replaced with the new motor. It only took about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Herndon, VA
- Parts Used:
- WB26X10038, WB06X10144
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Turntable coupler bore became oversized.
Small sized phillips screw driver was required. Once gaining access to the new motor the part(s) replacement was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine J from Yuma, AZ
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drive motor not working
There where five screws to remove to get the bottom off then two to release the motor from the housing pull the electrical supply cord out then reverse the process. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Tracy, CA
- Parts Used:
- WB07X10475
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The Grille Sub Assembly
The repair was quite simple. I removed the old grille assembly from three opening slots on the microwave and gently inserted the new unit into the (3) slots on the microwave. I used (2) screws to tighten down the unit securely. Done!!! It is working perfectly.
Was this instruction helpful to you?
Thank you for voting!