EMO4000JSS02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave stays on when door opened
Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from VIPER, KY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Blown fuse in microwave
One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clay from Kansas City, MO
- Parts Used:
- WB26X10037
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
A ratteling when the over was running
Unplugged the stirrer motor and the noise stopped. Therefore, replaced the stirrer motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Wood Dale, IL
- Parts Used:
- WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Cooktop light receptacle cracked
Remove screws holding bottom cover. Cover then swings down allowing access to the receptacles. Receptacles have a single screw attaching them to the appliance with a simple electrical plug supplying power. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NOSHIR from Sun City Center, FL
- Parts Used:
- WB02X10733
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace spent carbon filter
remove 2 screws from top of grille; remove grille by moving it to the left and then away.
remove old filter by lifting the front edge and then pull out, and replace it wih a new one using the reverse order of the above.
replace grrille and screws.
The repair is a 'no brainer'.
remove old filter by lifting the front edge and then pull out, and replace it wih a new one using the reverse order of the above.
replace grrille and screws.
The repair is a 'no brainer'.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Clarksville, MD
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Turntable coupler became brittle and fractured
I simply pulled the old coupler off the moter shaft after removing glass turntable plate. The coupler lifted right out since it was fractured. Luckily all peices came out attached. Typically you would need to remove the bottom access panel on the microwave and remove the turntable motor to install the new coupler. However you can simply snap off the extra plastic piece that is molded to the coupler to allow for an easy push down onto the shaft from the inside of the microwave cooking area where the coupler fits onto the moter. Piece of cake. I don't believe there is any danger in shortcutting this because the weight of the glass plate will hold it in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Pearland, TX
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace microwave light and broken base socket
Lower base of the microwave, about 6 screws,
replaced broken light bulb socket,then re-installed.
Installed new light bulb.
replaced broken light bulb socket,then re-installed.
Installed new light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from LaPorte, IN
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tray was brokenwhen moving
opened the door and put in the tray!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Fruit Heights, UT
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass turntable stoped turning due to broken coupler
Pulled out broken one with fingers, put on new one with fingers, it did not have anything preventing it from just slipping on. Didn't need to take anything apart to install me part.
Was this instruction helpful to you?
Thank you for voting!
Microwave powered up when door was opened
After researching on line and watching installation videos, ordered all three switches and installed. Disassembly of microwave was simple, removing the bracket holding the switches was a little tricky, it sits behind a metal post and you have to angle and wiggle it out. One note of caution when replacing all three switches, be sure to install correct switch in correct location. Had two of one style switch and one of a second style, and put one in wrong place, causing microwave to power up again when door was opened. After thinking it through and doing a second disassembly, and double checking installation instructions, corrected problem and microwave now works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from MADISON, WI
- Parts Used:
- WB36X10213
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Awkward positive to work
Slowly and carefully to protect bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Mesa, AZ
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable no longer went around
I followed the instructions provided by others on-line who had done a similar repair. I removed a handful of screws, disconnected the wires from the old drive motor and connected them to the new drive, replaced the screws that held the drive motor in place, and those that held the bottom housing in place, and I was done. Literally took less than 10 minutes. If I had known earlier how easy it was, the microwave would have been fixed much earlier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROGER from BLUFFTON, SC
- Parts Used:
- WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loss of lighting for over-stove illumination.
Must remove 5 screws in bottom of Microwave, which is hinged to the unit. Then simply remove the old lamp holders, and replace with replacements. Uses only a single screw for each lamp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Denham Springs, LA
- Parts Used:
- WB02X10733
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
needed replacing
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from Edison, NJ
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
coupler was broken
removed the broken coupler and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!