EMO3000CWW04 General Electric Microwave - Instructions

We removed the top vent panel and the door lifted right off. The hardest part was figuring out how to get the handle off the door. The web has easy to follow instructions so we got the inner plastic seal removed and all the screws were exposed for the handle. Once the handle was off, we pryed the melted part out of the door frame and replaced it, after cleaning the glass on both sides. Once replaced, the oven looked new again. We spent $60 for the part, rather than $450 for a new oven!

Followed instructions listed here that I needed to separate the inside facing on the door with a butter knife so that I could see the two screws that held the handle in place. Easy off, easy on. And I am NOT a very good handy man.

I replaced old tray with new. Received replacement part in two days. I was surprised at the quick response time. The part ordered was right the first time.

Remove top air grate via 2-screws. Remove metal top panel behind grate that's above bulb via 1-screw. Bulb is exposed and can be un-screwed. DONE

Decided to replace entire door assembly since there was a small break in the door cover as well as the handle. To remove old door: take out the two screws that hold the vent cover above the door. Open the door and lift up to release from hinge pegs. Reverse process to install new door. Very Easy

Gently remove the interior trim with a putty knife. Remove the two screws holding the old handle in place. Replace the new door handle. Screw the new handle in place. Align the trim and snap it back in place. Confirm the door handle is secure. I applied a little Gorilla Glue to the new handle for added strength before screwing it on.

Simply ordered a replacement part that was quickly and coveniently mailed to my home.

Handed the part to my son. He unscrewed 5 screws in the base of the microwave, it dropped down. The light mechanism was clearly in view. With the exception of some corrosion on the old piece, it was simple to remove and replace, put back together, screw back up and all worked fine.

Phillips screws on bottom panel allowed me to install new socket and put electric connection back. Secured bottom panel and that was it.

It took less then 10 minutes to order. Received new part with 3 days

Put it in place. Ordered replacement over internet on Wednesday and part arrived Friday. Very fast service!

Piece did not fit as well as old piece needed to take off a small piece to make it fit. Once it was in the turntable worked again

Removed bottom cover of microwave, involved removing 7 screws, removed turntable motor, involved disconnecting wire harness plug, and 2 screws, connnected wiring to new motor and reinstalled with original hardware

Popped the inside trim off took out the screws for old handle reversed process

My microwave was squealing horribly and replacing the turntable motor (SUPER easy btw) didn't fix it. So I figured it was a spun bearing or bushing in the cooling fan (spoiler alert -- it was!). Installation was simple and did NOT require removing the cabinet-mounted microwave from its position above our stove: Unplug microwave, carefully unscrew the 2 screws holding the vent grate above the door, remove the grate, then unscrew the one screw holding the top of the control panel to the case. Carefully pivot top of control panel down and unhook it from the case (at the bottom of the control panel there are two little legs or extensions that insert into slots in the case). Then disconnect the 3 or 4 wires that attach the control panel to the wiring harness (I marked them each with tape so I would remember where they go, but you can just take a picture with your phone). Set the control panel aside. Where the control panel was, you will be looking at the fan, with a bunch of wires between you and it. Take another phone picture for reference, just in case. Disconnect the various wires, starting at the top right and working your way around clockwise. I marked each wire with a piece of tape and a number, starting from 1 and working my way around an imaginary clock face. I think I got to 12 and then the last two (sort of buried in the middle) I labeled as "0" and "-1" but you can use any numbering series you like. Once the wires are all disconnected you can gently push them aside and unscrew the two screws holding the fan assembly in place, and disconnect the fan wire. Then gently maneuver the fan assembly out the front of the case. Installation is simply the reverse of this simple disassembly process. Voila! Back to a nice quiet microwave.