JVM1431WA01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Newbern, NC
- Parts Used:
- WB06X10436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
change microwave fan discharge from front to top
damper plate was a snap-in part. rotated fan discharge to top of microwave. installed ducting to discharge food odors outside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Zebulon, NC
- Parts Used:
- WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bulb separated from base, leaving base in socket. Unable to remove base without damaging socket.
Removed 5 phillip screws from bottom plate of microwave oven to lower the plate and gain access to the socket. Then, removed screw(s) attaching socket to the oven. Installed socket, and secured the bottom plate of the oven with screws removed previously.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Carson City, NV
- Parts Used:
- WB2X9883
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Filter old, needed replacement
Remove 2 screws, remove cover, remove filter, reverse proceedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Springfield, IL
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Insulator around light socket Broke.
Took out five screws on microwave bottom, removed the two screws in the socket and unplugged the light socket. Plug in new socket, screw in place with 2 screws. Lock in microwave bottom,and screw in 5 screws. Replace bulbs. Be sure and either unplug microwave or switch off at electric service box, before starting. Of course, hubby did all the work, but I supervised.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from MADISON, WI
- Parts Used:
- WB2X9883
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
needed to replace charcol filter
followed the easily understood step by step instructions from the owner's manual
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda P. from Naples, FL
- Parts Used:
- WB2X9883
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
filter in fan over stove had not been replaced since we bought this place.
My husband simply unscrewed the front of the vent, pulled out the old filter and slid the new one in. After cover was washed and dried, he screwed the cover back on and Voila!The vent fan is much quieter now and it clears the air quickly when it is in use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRIS from SPRING, TX
- Parts Used:
- WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light bulb fused it self to socket
replace socket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Bluffton, SC
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burned out lightbulbs.
Changing 2 lightbulbs is NOT ROCKRT SCIENCE. With a screw-driver, remove the under MW light lens, unscrew the 2 burned out light bulbs, and replace with 2 new quality light bulbs. Test out that both are lite and working as they should, replace the lens and you are done, Until you find out one of the new (made in Chins) light bulbs is burned out after about 6 hours of being lite, call the parts phonr number and order a new replace bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Arlington, TX
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light bulb in the over-stove microwave
Removed the one phillips screw that holds the light lens in place, drop the lens down for access to the burned out bulb, screw in the new bulb, replace the lens.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from schererville, IN
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad bulb
unscrewed cover, took old bulb out, screwed new bulb in.relaced cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerri from north haven, CT
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out bulb /microwave
simply to install new bulb. Unscrewed the under the microwave lamp door with a screwdriver. Inserted new bulb into socket. good to go
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATRICIA from ALEXANDRIA, VA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace micro/hood combo stove light
simply unscrewed protective lens cover, and swapped bulbs--these bulbs are great--last for years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DALE from ST PETERSBURG, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Over Stove Light Bulb Out
Took screw holding lens cover out, dropped cover down, unscrewed old bulb, screwed new bulb in socket. Screwed cover back in place. This is the third bulb in this socket, the other bulb is original.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Riverhead, NY
- Parts Used:
- WB2X9883
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dirty rotted filter
great correct part thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from La Crescenta, CA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb burned out
Easy as can be. Removed one screw on the glass cover, removed two burned out bulbs and reinstalled two new bulbs, reinstalled the cover and all is well now. The best part - my 'supervisor' is happy that she can see to cook again!
Was this instruction helpful to you?
Thank you for voting!