JE635WW03 General Electric Microwave - Instructions

After looking up on the computer a schematic of the unit, all that was needed was removing four screws to remove the top and side cover which was one piece.
Next was removal of electrical connection to burned out lamp, then removing burned out lamp and installing the new lamp and reconnecting electrical connection.
Job was complete after reinstalling the cover.

Microwave now working with new lamp lighting when in use.

Continuity checks showed the flame sensor was open. Schematic notes it opens at 217 degrees and closes at 30 degrees. Removed sensor and placed in freezer for twenty minutes. Tested sensor and it was now closed, reinstalled and microwave worked normally. Ordered new sensor in case the original is operating at too low a temperature.

I took the cover off and followed the electric current to see if it got as far as the display.
I did not get past the thermostat shut off where the current stoped. I jumped the thermostat and the unit worked. The part was so inexpensive that I decided to replace it rather than try and freeze the old one in hopes of "reseting" it.

PS240270
Ceramic Fuse - 15 Amp
Easy installation , remove microwave cover housing ,locate fuse by door catch & replace..
Received quickly..
Replaced fuse , removed microwave cover housing , located fuse adjacent door catch removed & installed new fuse...

Thanks to great instructions from a previous person, this was super easy. It took 5 minutes to remove and replace the new motor. The big part of this job was cleaning out the cabinet where the microwave sits, since I had to take it out.

There is a 'door cover' pressed into the bottom of the microwave, that just has 6 small tabs that you need to cut. Then remove 1 screw, and the wire clip and the motor is changed. The door just reverses and re-installs with 1 screw. When the microwave was designed, this repair was in the engineers mind. So simple I couldn't beleive it.

I detached the metal plate on the bottom of the microwave that once removed by cutting the metal tabs could then be turned around and put back in place with 1 screw. The old motor was easy to detach (1 screw) and unplug. Hardest part of the whole project was finding where to get a replacement motor so I'm glad I stumbled on your website. Once the part was received it took just a couple of minutes to replace and it works great.
My husband called about getting it serviced and was told it would be at least $100 just for labor, parts would be additional. I'm now an electronic goddess in his eyes....

removed cover and tested fuse, fuse ok, check flame switch (thermostat) bypassed it with thin wire ,all power on!!...ordered it, got it, replace it within 5 min, as soon as part arrived.

I happen to have a set of "security" screw driver tips which are required for this appliance - available for about $10 at Home Depot or Harbor Freight. Remove three security screws from back of housing, lift up and aft to remove the cover. The light is on the left in a "snap in" mounting so use a flat blade screw driver to push back the retainer and lift out the old bulb then disconnect the two "push on" wires and install the new light. Total time about 10 minutes. The only issue is the requirement for a security driver set.

Traced out 120volts from neutral to hot though fuse, and "high limit" switch screweed to far side of oven exterior cavity. High limit thermostat was "open". Jumped it out to see if unit would produce heat. Melted 1/2 cup of ice in thirty seconds. Ordered new part. Later foud out hi limit can be "re-set" by subjecting it to sub-freezing temperatiures. This is true, but I installed new part just to be safe. Machine is working fine now and has been in daily srvice for over two weeks.

It pays to troubleshoot a broken appliance before thinking about buying a new one. I removed the cover and found the manufacturer's circuit and troubleshooting diagrams inside. The fuse was good, next in line was the flame sensor. Meter showed it was open, so I knew that was it. Disconnect the wires and screw, replace part, replace cover. DONE! I knew I had the right part from the pictures on PartSelect's web site. Total cost under $20 compared to ten times that for a new one. Had the part in two days.

removed 3 screws to take off outer housing ( did not have proper screw driver but was able to remove with pliers). used flat head screw driver to pry light socket w/bulb off of snap-in mounting & unplugged socket wire attachments. plugged in & reattached new part.

I unplugged the microwave and turned it over. It was easy to spot where the motor was located. I noticed the cover had little tabs holding it in place. I noticed it had brackets that could be snipped and the cover reversed so the little tabs and hole for the metal screw could be installed. I used snips and cut the little tabs and removed the cover. The motor had one screw and a tab that held it in place. I unplugged the motor first removed the screw and changed the motor. Then I plugged it into the wiring harness.The plastic piece for the turn table dropped out. I used pliers and straightened the tabs turned the plate over and put two small extensions in the slots and removed the metal screw and pushed the tabs in place and the metal screw through the hole and tightened. I then set the microwave in place and opened the door and pushed the plastic piece into its proper place. I then got a cup of water and heated it up.

On the bottom of Microwave I cut the 6 clips holding the cover in place with side cutters. Removed the one screw holding motor in place. Un plugged it. Plugged in new motor, replaced screw. Filed off sharp points of clips. Slid cover tabs into slots, put screw in cover. Replaced parts inside oven, turned it on, it worked.
I did this twice. The first time the plug fell inside the housing and I had to turn the microwave over to fish it out. So when I received new part I left it plugged in. I should make it clear I am talking about the plug to the motor not the one to the microwave. Of course I unplugged that before I even moved the microwave. Thanks to another customer and his repair story because I was dreading the chore of dismantling the entire microwave to get to the turn table motor. He made it so easy. Thank you for having the part and great instructions.

This was an under counter microwave located above the range. There is a cover on the bottom of the unit that contains screens for the fan. This cover is removed by taking out 3 screws located near the front of the unit. Be sure to support the cover when removing the last screw. There is a plug-in wire going to the turn table motor. Unplug it so you can lay the cover on the range top. The motor is removed by taking out two screws and pulling down. It should not take much force as it slides into a plastic drive located under the turn table inside the microwave. There should be specifications on the old motor that match the new motor. Push the new motor up into the plastic drive unit, matching the "D" shaft of the motor into the plastic drive. Replace two motor screw in correct holes so that the plastic drive is centered in the hole. Plug the motor back in and replace the cover.

I found an exploded view diagram of of my microwave model which was very helpful. You need only remove outside metal skin by removing 4 screws on either side and 4 more on the back. Remove 4 plastic hole plugs from the top mounting inserts. Gently pull sides out and lift up and back to remove outer skin. The fuse is located on the back right corner behind the control panel. You access from the side. The fuse is under the spreader bar. Lift fuse up gently to remove.

P.S. It was the MSP Capaciter and or the interlock switch, snap apart 21A (19) failure that actually caused the ceramic fuse to blow.