JVM1490CD002 General Electric Microwave - Instructions

Unpacked glass plate from cardboard box and placed atop rotating spindle inside oven - done.

Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.

Our GE Profile Advantium 120 Series Over-the-Range Microwave stopped working. We called GE Service. The first available appointment was two weeks after our call. The technician charged $99, gave us a form stating that the Magnetron and Diode Cable as defective and quoting an additional price of $362 to furnish and install these parts. He said that it would be another two weeks before he could do the work. Instead I ordered the parts from you and had them within two days. The parts you furnished were identical to the original parts in our unit. They arrived within two days. I installed the parts without removing the microwave from the wall. The most difficult part was inserting the magnetron mounting screws into openings in the rather tight space available. I was able to do this by using plastic pacaging tape to hold the screws onto the end of a short Phillip screw, Prior to iserting each screw I pushed it through the sticky side of a piece of packaging tape. I then folded the sticky surface over the shank of the screw. Once a screw was seated, but before it was fully tightened, I used needle nose pliers to pull off the tape. The unit now functions perfectly.

Snap the plastic trim piece from the inside of the door off.took broken latch out and put the new one in.PS your part came really fast.Thanks

My son said order it. It came a day later. Very cool. He took the door off and up to his room. No idea what tools except most likely a screwdriver. I asked him how did it go. He said it's good. Nice...

Removed the door, removed the old choke cover (breaking all the stap catches), removed the slide door latch assembly from the spring (the most difficult task) then reassembly of the latch to spring, sliding into the grooves along the inside of the door, the installing the new choke cover (very easy with the new one) taking care not the break any of the staps. Easy enough! Another difficult task was to re-install the door to the frame. It appears that the lower "hinge" is slightly bent down to allow easy install but the door now makes a slight sweeking sound when opening and closing.

removed cover an replaced

I held the door open while the repair man took the black facing off and replaced the latch and reinstalled the facing I was worn out

ordered matching handle on internet. Pried black plastic panel off inside of door--PLASTIC TABS HOLDING PANEL BREAK OFF EASILY AND MAY KEEP PANEL PERMANENTLY LOOSE--good luck! Metal frame holding window glass pried off of front of microwave(AGAIN PLASTIC TABS HOLD IT AND CAN BREAKOFF) use small wedges to pry tabs up and off metal frame. Remove screws holding handle, screw on new handle (very firmly) and assemble in reverse order.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

Removed outer cover and then replaced the T. C. O. located on the left upper side if the unit. Replaced outer cover, tested oven. Oven operates normally.

Read instructions and viewed video. Project would have been very difficult without the instructions and video. Step 1 removed vent grill at top to microwave, by removing two scres. Step 2 removed microwave door by lifting. Step 3 used a one inch plaster knife to separate the plastic interior cover of the door. The video was most helpful. Use the thin blade of the plaster knife to locate snap locations of the plastic cover. Step 4 removed broken latch by applying slight pressure to the outside. Observed the attachment of the 'spring'. Step 5 installed new latch and spring. Step 6 reinstalled interior plastic cover. Step 7 install door. Step 8 install vent cover with two screws. Step 9 test unit.

Take the pliers and place a tight grip on the broken rack bracket, twist toward front of microwave until loose, pop out and by hand insert new rack bracket, twist toward the back of microwave until fully in place. One side was slightly harder than the other taking off and replacing rack bracket.

Actually, my brother did repair and I helped. The hardest part was getting the black liner inside the door pried loose. We managed after prying gently with a screw driver to pop it off. That was the most time consuming part.

I had left the door to the microwave open and turned around and hit the door latch assembly with my arm, sanpping off the bottom latch hook. In an effort to take apart the latch assembly it was necessary to take off the door choke cover and in doing so I sanpped a few of the plastic tabs that hold it in place. Undismayed, I then went online, found PartSelect, ordered the replacement parts, received them in three days and in fifteen minutes fixed both of them. The diagrams on the site made it easy to find what I needed and ordering the parts was easy. Thanks PartSelect-my wife is happy again!!!