JVM1651WB03 General Electric Microwave - Instructions

Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.

The repair was simple. It was just a matter of removing the upper vent grill to access the screws for the panel frame. Then I just popped out the old frame and installed the new one. The PartSelect website allowed me to see a visual map of all the parts of my microwave which allowed me to find and choose the right piece for the job. It only took 15 minutes for the start to finish repair.

ordered 2 new sockets and bulbs easy replacement great service from this site

I first read the previously posted directions from other customers that were sent with my part order confirmation, which were all very helpful. Then, I basically used a screw driver to unscrew the screw holding the lens cover in place - be careful as it is a very tiny screw and it can easily fall behind your oven. You might want to place a large piece of cardboard over the space between oven and wall, as I did, so that you don't lose the screw in case it falls. Next I pried open the prongs, carefully slid out the cracked lens, and slid the new lens in place, pushed back the prongs and put the screw back in. I found that it was easier to use my fingers to first place and tighten the screw because it is very small and will keep falling out of place if you try to just use the screwdriver. Good luck!

Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.

Wow! It really was as easy as everyone says. I ordered the part. It came overnight. I took out the 6 screws on the bottom of the microwave (AFTER unplugging the microwave of course), unscrewed the part and unplugged it, put in the new motor, plugged it in and screwed it in, and replaced the bottom screws. The only trouble I had, which really has nothing to do with this part or the repair, was that some of the screws on the bottom of the microwave were very difficult to replace as they didn't seem to line up with the holes beneath. I had a handyman coming to do some deck repairs and had him put those in. Ah well. I did MOST of it myself.

Stephanie, age 52

Remove air inlet piece with two screws. Remove one screw holding the frame on. Whole keypad with frame is loose though still attached with wiring. Remove old frame from keypad and replace with new and reinstall.

Very easy repair to replace filters. Step 1: Note position of filter and which end is towards you and position of latch handle. Slide old grease filter away from you and forward until it drops out, Set it aside. Step 2: Take new filter and put in slot away (as you noted) from you then slide towards you until seated properly underneath microwave. Repeat steps for the second filter. It takes about 2 minutes.

.Thank You Dan

My son did the repair for me. He only had to use a screwdriver. He removed the panel ,took the old on off and put the new one on.

replaced

There where five screws to remove to get the bottom off then two to release the motor from the housing pull the electrical supply cord out then reverse the process. Piece of cake.

Removed the 6 screws that held the cover below my microwave. Unplugged the part, plugged in the new one and I was done. My part arrived from you just one day after I ordered it! It was my first microwave repair ever, and it couldn't have been easier.

I removed the screws that held the bottom in and then dropped it down to access the motor. I removed the 2 screws that held the motor in and unplugged it. I then plugged the new one in and reattached it with the 2 screws and put the bottom back on. It took me about 5 minutes to fix it for only $40.00.

removed the bottom plate from microwave and replaced parts