JVM1660CH04 General Electric Microwave - Instructions

ordered 2 new sockets and bulbs easy replacement great service from this site

Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.

My microwave is built in above the stove which provides lighting and fans for my stove. The glass lens cover for the lighting was cracked in several places and the light bulbs had burned out. I taped the glass lens for removal so it didn't break apart due to the cracks Removed the one screw. .Both light bulbs broke away from the base sockets as I tried to unscrew them. I used electrical tape wrapping in reverse on a lightbulb (socket end) so it was sticky for a grip on the base, shoved it in the sockets and was unable to unscrew the broke off bases. So it was very successful and no repair man was needed.

unscrewed the screw, pried up metal tabs that hold in light lens. took out broken pieces, slid in new light lens re-secured tabs with fingers, screwed in the screw again.

Just removed the screws from botton of unit, unplugged and removed the burned up motor, reveresed the process to install new motor. Less than 10 minute job.

bought a replacement for it

Easy peasy - removed lens holder w/screw driver. Cleaned cover after removing damaged glass lens. Then unscrewed burnt out light bulbs. Installed new bulbs, slid in new light lens into holder and screwed back into bottom of microwave. Removed greasy filter and slid in new filter. Done!

I diagnosed the problem myself. I googled GE parts and was refered to you guys. I ordered the part and it took less than a 5 days to arrive. I used a phillips scewdrive to remove the cover of my microwave and removed the turning glass motor. This took less that 30min and cost less that $50.00. I figured that it would have cost me approx $125.00 to get a tech person to my home for this repair.

Thanks a lot!

Bernard

unsrewed the bottom of the microwave(there was about five or six screws)located the motor unpluged it and unscrewed the two screws holding the motor once installed i reversed the proceedure and put everything back together...simple as 1,2,3...

I turned off the breaker/electric power to the microwave; opened the base of the microwave, detached the wire to the old drive motor, removed the
screws holding the drive motor in place; removed the old drive motor and installed
the new drive motor---beyond easy!!!

Thank you!

Simply removed screw, pulled down light holder, unfoled the metal tabs, took out the broken pieces and replaced the glass lens and light bulb.

I took the glass table up and underneath was the turntable coupler. I reached in with my hands and gently pulled the old coupler out. Once out I lined up the new one and gently pushed it in the hole until it locked into place. The process took about 5 minutes to complete. Very easy to install.

I removed the screws that held the bottom in and then dropped it down to access the motor. I removed the 2 screws that held the motor in and unplugged it. I then plugged the new one in and reattached it with the 2 screws and put the bottom back on. It took me about 5 minutes to fix it for only $40.00.

Removed 5 philip head screws from under panel. Under panel droped down exposing drive motor. Removed one drive motor screw, replaced with new motor at the same time lining up new coupler. Pressed together, reinstalled motor srew, attached wire coupling and tested. Worked fine. Reinstalled lower panel screws (5)and unit was ready to go. I ordered two of each units because I believe this to be weak link in the unit. It was only 2 years old, used little as I have another home. I recently installed a like unit (Hanging) and it was a breez. 4 srews properly placed, electrical cord hole properly drilled & ready to go in 45 minutes.

Remove the 8 screws in the bottom pan covering the bottom, unpluged the lights and motor plug-ins, slid or pulled the pan forward or to me and removed pan. prized the triange piece which fit into the glass tray to turn it to remove it. removed the two screws which held the motor in place. presto, got the model # off the inside panel and ordered the part on the compiiter, \. arrived in 5 days.
P.S. cleaned everything while I had it apart, toke longer than chancing the part.