JE2160BF03 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rebecca from EDINA, MN
- Parts Used:
- WB06X10500
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The original feet, two disappeared. Uneven microwave.
Fast & easy. I was able to determine that this foot would work from the descriptions on online!! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from POTOMAC, MD
- Parts Used:
- WB27X10567
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Power cut off to Microwave - It was run empty
1. Remove trim kit - Philips head screw driver
2. Remove Microwave from the wall - Philips head screw driver
3. Remove outer microwave cover - required tamper proof torx bit drivers
4. Replace Magnetron thermostat. On this model there are 2. in this case it was on top of the unit tied into the wiring harness to the main panel.
5. Reinstall microwave and trim kit
2. Remove Microwave from the wall - Philips head screw driver
3. Remove outer microwave cover - required tamper proof torx bit drivers
4. Replace Magnetron thermostat. On this model there are 2. in this case it was on top of the unit tied into the wiring harness to the main panel.
5. Reinstall microwave and trim kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earnest from WINCHESTER, CA
- Parts Used:
- WB02X10895
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
1 of 3 roller wheels came off
Removed old roller assembly and installed new roller assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from GAINESVILLE, TX
- Parts Used:
- WB27X10682
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Everything Worked Fine But It Stopped Heating The Food.
Take the four saftey torx screws off the back of microwave that hold the side panels on. There are no screws in the front. Just pick up the side panels a little and slide towards the back of microwave and it will come off. The magnetron is visible behind control panel. Unplug the magetron, take a 3/8 nut driver , remove the one bolt that holds it on , remove and replace with the new one. Plug the wire (it will only go one way) back up and replace cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Portage, MI
- Parts Used:
- WB27X10907, WB27X10888
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
was loud when cookiing
Went well, very easy to change once the microwave was out of the wall. Sounds better than when it was new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from New Orleans, LA
- Parts Used:
- WB02X10895
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problems
Remove the Glass rotating tray and replace the guide
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beth from Katy, TX
- Parts Used:
- WB36X10241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original barrier screen on the microwave bubbled and became warped after popping popcorn in microwave.
I slid the original barrier screen out of the door and slid the new one back in. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Hanover Park, IL
- Parts Used:
- WB24X10103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
tray would slowly rotate when door was open.
I determined that one of the 4 micro switches that interface with the door was faulty. Ordered that part and replaced it. Had to remove the cover and front control panel (without removing any connections. Two philips screws hold the limit switch assembly to the bracket. After removing those screws, twist the whole switch assembly clockwise around the mounting frame and now you can remove the defective micro switch and replace it with a new one. This works for any of the 4 switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Laurel, NY
- Parts Used:
- WB49X10108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass cooking tray broken
Simply replaaced broken cooking tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Warner Robins, GA
- Parts Used:
- WB49X10108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass tray
just placed it on the wheel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corey from Greenville, NC
- Parts Used:
- WB27X10682
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Micowave not heating food.
I just took off the cover, located the magnetron, replaced it and slapped everything back together and since then everything's been working pretty good.
Was this instruction helpful to you?
Thank you for voting!