EMO4000JBB03 General Electric Microwave - Instructions

I initally thought the problem was the turn table motor but after installing that motor & not being successful I realized the problem was the stirrer motor.Removing & insalling that motor was a bit more challenging but worth the effort as I saved either the cost of a repair technician or the puchase of a new one.The microwave is back in service & running fine.

All electrical worked (fan, lights, control panel) door switch was broke. Pulled the oven out. Took out two big screws from the cabinet above. (be careful not to drop oven)Set the oven on kitchen counter. Took off five screws that held the vent cover. Removed vent cover. Took out one screw that held the control panel. Lifted, turned and slid the panel into the space below so I could get to the upper door switch. Replace door switch and re-assemble.

I looked up the parts of the microwave on Part Select to see if there might be something I might be able to do myself. I found that the Cooking Tray drive motor was the problem. I ordered the part and got it the very next day. I loosened the 6 screws to the lower part of the microwave and then the two screws that held the part in place. I removed the element and pulled the wire plug from the element, placed the new element back in with the screws, repluged the wire, placed the lower cover back to the microwave, tested the microwave out and, is still working quietly as if it were new. Thanks to part select.com it was easy.

After finding the part on PartSelect, ordering it online, receiving it quicker than expected -- it took me 5 minutes to unscrew the bottom cover of the microwave, take off the old motor, replace with the new motor, screw the cover back on and test the WORKING cooking tray drive motor.
Very impressed with the efficiency of PartSelect. It's web page was easy to navigate. Thanks.

Found this site, was able to identify the specific part through the internal search engine, very user friendly.

Read what others had said about similar repair. Now with confidence, removed screws, got easy access to the motor, removed motor, installed new motor, re-installed bottom cover, done!

If you have electric burner or gas stove, I suggest laying down a towel or similar cloth. In the event you drop a screw, you done want it bouncing off the stove surface, or down into the burner dishes.

Great site, great resource, super fast shipping.

I unscrewed the entire undersurface of the microwave (I didn't do this before!) and replaced the light socket. Easy job and I'm glad the part was still available.

Rather than open access door took off bottom (5 screws) This gave more room as the microwave is mounted under the wall cabinets over the stove.

I was told by 2 different appliance technicians that the crumbled/melted light socket could not be replaced which meant replacing the entire microwave (expensive!). Other posters on your sight described the repair steps and I gave it a try. The hardest part was probably figuring out which switch in the fuse box belonged to it (now marked clearly). It was a simple matter of unscrewing the bottom panel of the microwave to access the socket, pulling the crumbled/melted unit off and shoving the new one on. I can't believe the repairmen didn't want any part of even giving it a try.

Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again

Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

Ordering was simple Recieved part day after shipping. 3 days sooner than I expected.
Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done.
Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.

first i remove the screw, then removed the lens assembly (really a frame) bent the feet out of the way, slid the old lens out and the new one in, bent the feet back in place and inserted the assembly into place replaced screw. the killer is a day later it was broken again, think the lens can't handle the heat from the oven below or the lights above. you guys where great fast and exact match part but the ge design is flawed

I removed both sockets from the microwave and when your part arrived, I installed them both including the new lights. The work perfectly and it was very easy to put them in. I also appreciate the speed of delivery and your concern for my feed back on the product. I have you number in my contact list and should I need another part, I'll check with your first.
thanks you

Took the screw out of the glass door holder, bent the clips up and removed the broken glass. While this was open chenged the light bulbs as well. Put new glass in bent the holding clips down and closed the doors and installed the screws again. So nice to have good light again and also new glass in them. Never noticed they were broken before.

BY THE WAY PARTS SELECT IS VERY PROMPT AND I RECEIVED MY PARTS IN ONE DAY AFTER THEY SHIPPED. SHIPPED ON MONDAY GOT THEM TUESDAY, thanks parts select for your promtness and speedy work for shipment.

took of cover removed switch and replaced with new one