JVM1190BD001 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ernest from Riverview, MI
- Parts Used:
- WB27X10585
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
oven made a loud buzzing & would not heat
completly removed outer cabinet,discharged capicator,removed some internal parts so I could get at the magnetron,
.removed replaced magnetron,reinstalled inner parts& cabinet .tested microwave viola
everything worked again.
Thanks, PartsSelect
Ernie
.removed replaced magnetron,reinstalled inner parts& cabinet .tested microwave viola
everything worked again.
Thanks, PartsSelect
Ernie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from CONCORD, CA
- Parts Used:
- WB15X10092
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
handle broke
pulled the trim off. took out the bolts holding the door on. removed door. took the door apart and replaced handle. put door and trim back. just like a brand new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Tonto Basin, AZ
- Parts Used:
- WB27X10227
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
A power surge damaged this and other appliances.
Removal of this "over the counter" appliance was required. After wrestling the appliance from the wall ( the most difficult part of the job) the cover was removed for a visual inspection. The circuit board revealed burned resistors and a capacitor was fried. The 15 amp fuse was not blown. I was able to loosen the circuit board from the framework by removing a few screws and unplugging the leads that were connected to the board. There are two screws inside the oven door jam that secures the circuit board. Once these are removed the circuit board can be pulled out to a point where the screws that hold the circuit board and wire connectors can be accessed and removed. A new circuit board can then be installed simply by reversing the prosses. The board was slightly over $200.00 but my oven was a combo microwave/convection. A new microwave/convection oven would have at least $500.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from YONKERS, NY
- Parts Used:
- WB6X60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
While removing for cleaning, grease filter fell behind stove. Could not be retrieved.
Simply slid new part into track holder by hand.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from LOCKPORT, IL
- Parts Used:
- WB6X60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dirty grease filters
Slide out the old ones then slide in the new ones. A 30 second job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Bloomington, IN
- Parts Used:
- WB15X10092
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door handle snapped off at lower screw
I removed the screw cover on the inside of the door, by wedging a flat-head screwdriver just under the lip, to 'pop' it off. I then removed the upper and lower screws with a Phillips screwdriver, and the handle came free. Then I simply reversed the process with the new handle, and popped the screw cover back on. Amazingly easy, and saved me over $100 from the GE website, as well as other 'parts' websites, which insisted I needed to buy an entire replacement door! Thank you for the service you provide!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from UNIVERSITY PA, MD
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb burned out light that is under the microwave, which lights the oven below.
thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from TREASURE IS, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Under the microwave there are two light bulbs that light up the top of the oven/range.
Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Marina Del Rey, CA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb wouldn't light.
Removed difuser (one screw), removed old bulb, screwed in new bulb, replaced difuser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon F. from Brookline, MA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right hand surface lamp burned out. It apparently fald up and broke the glass cover. I wne on line when I found out the only local deaaler was some miles away and more expensive.
Simple. The parts came instantly. The glass was too big so I had it cut to size. I unscrewed the fixture with a screw driver replaced the bulb and slipped the glass cover into the frame and screwed the whole assembly in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois Jane from Fernley, NV
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light bulb burned out
took out several screws dropped down the panel under the microwave and unscrewed the bulb and put the new one in. It was a simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Waldorf, MD
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Interior Light Out
Removed Cover Plate,
Removed back cover
Bulb disintegrated removed base with pliers
Screwed in new lamp
Replaced cover
Done
Removed back cover
Bulb disintegrated removed base with pliers
Screwed in new lamp
Replaced cover
Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY from PLYMOUTH, MA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Underneath Light On Microwave Would Not Come On.
My son=law did repair because I am elderly and it was necesary to remove the bottom plate of the microwave which I was unable to do. The microwave was installed in 1987 and I believe this was the first time to replace the bulbs. When my son removed them the bulb was diintergrated. That's how old they were. Once he was able to remove the underneath plate the repair was easy except for removing the old bulbs. I think that I could have done it myself but he was available and I am sure it was done much better. All in all the parts)bulbs) were correct and everything is workiin fine. This is a good place to order replacement parts. In fact I am going to order a new charcoal filter. He took the label off the old one and I am ordering the replacement. After all 1987 may have been a good year, but time for a new one. Mary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samar from Fairfax, VA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb under the microwave was burned out
changed the bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy Ann from Fort Pierce, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bulb was burnt out
Just unscrewed the screw holding the lens, unscrewed the bulb and put the new bulb in. Simple
Was this instruction helpful to you?
Thank you for voting!