HVM1750DM2BB General Electric Microwave - Instructions

Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...

I replaced the switch at the bottom per instruction. I had both switches. I think it was the monitor door switch.It works fine now. Thank you Part Select .

Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.

Ordered a replacement grill, replaced the optional charcoal filter at the same time. Took just a little effort to get the alignment tabs in place--required just a little more elbow grease than you'd think, then replaced the two screws.

I examined the grille (at that time I didn't know the name of the part. It appeared to be an easy fix. I wrote down the serial number of the microwave and googled for the part. I ordered the part and replaced it. It was very simple and I'm not a fix-it person. My husband was amazed.

Per instructions on part select.com website. But needs further repair because still doesn't heat food and pad is partially disabled.

I replaced old tray with new. Received replacement part in two days. I was surprised at the quick response time. The part ordered was right the first time.

Removed one screw, slid frame out and removed broken glass. replaced bulb. The hard part was slidding the frame back in place and starting the screw. We were very surprised at the fast delivery of the parts, thank you. The sad part, a few days later the glass broke again. We are trying to get to the people at GE to solve our problem. We feel like that will not happen, we just do not have the time to stay on hold on the phone waiting for someone to solve our problem. Will reorder glass.

I purchased the fuse and 3 door switches from PartSelect. Replaced the fuse first but that did not solve the problem. Then I replaced the 3 door switches and problem solved!! So fuse only cost $5.00 so glad I have a new fuse in there as well. To see how to replace door switches see videos on utube!!

Simply ordered a replacement part that was quickly and coveniently mailed to my home.

Remove top air grate via 2-screws. Remove metal top panel behind grate that's above bulb via 1-screw. Bulb is exposed and can be un-screwed. DONE

There is a plastic vent cover located above the microwave door on this over the range model. On our unit, it was held on by 2 screws into tabs located on the top of the cover. Those tabs had broken off. The replacement did not have two tabs on the top of the piece. It had 4 small tabs along the bottom of the piece that fits into the edge of the unit directly above the microwave door. The tab holes are already there so it is just a matter of snapping the cover tabs into these holes with a slight tap or push. No tools required unless you need to unscrew the old cover (ours fell off). Total project time was less than ten minutes.

Phillips screws on bottom panel allowed me to install new socket and put electric connection back. Secured bottom panel and that was it.

Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!

Handed the part to my son. He unscrewed 5 screws in the base of the microwave, it dropped down. The light mechanism was clearly in view. With the exception of some corrosion on the old piece, it was simple to remove and replace, put back together, screw back up and all worked fine.