JVM1851WD001 General Electric Microwave - Instructions

Dropped the bottom of the microwave,removed the two screws holding the motor in, disconnected the electric wires, reversed the procedure and it worked like new!

ordered part from partselect received in about 3-4 days removed 6 ea screws from lower panel , removed 1 ea screw holding motor in place, pulled wire receptacle loose from motor, threw old motor in trash, put new motor up into plastic tray rotating device turned motor to secure on one side and installed screw to hold motor reinstalled wire plug and panel ops ckd good about 15 minutes to do could have done it quicker but my eyes ain't what they use to be Very easy fix when you get the right part and I got it on the first order with partselect ......Thank You Very Much

Disconnect power to microwave. Remove plastic rotor attached to motor shaft. I had to pry up from underneath it with a screwdriver to break it loose. Cover surface below microwave as bottom cover screws are small and easily lost. Remove three front and two rear screws from bottom cover and it will swing down. Locate the drive motor on the cover, disconnect the power leads, remove one set screw and rotate the old motor off the cover. Reverse instructions to re-install new motor. Swing bottom cover back up and re-install the five small screws. I had a little trouble lining up the screw holes and it helped to use a finishing nail to align the holes in the cover with those in the microwave frame. Reinstall plastic rotor on motor shaft, reconnect power to microwave and test the turntable.

Using a phillips screwdriver, remove 7 screws from the unerpanel of the Spacesaver Microwave. The panel will swing down from the rear edge hinge, exposing the lights and the stirrer motor. Remove the electrical connector and two screws holding the motor in place and remove the motor. The stirrer inside the oven can then be removed if desired. Install the new motor in reverse order. Note rotate the stirrer inside the oven to align the motor shaft to facilitate assembly.

Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.

Replaced the filter cartridge.Problem solved.

removed old part and replaced

Opened the light cover. Removed the old light bulb using a light tug on the old bulb, lined up the new bulb and pushed gently into the socket.
Turned the power back on and the microwave is good to go.

-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order

thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)

however, I had hit the cook button and the microwave did not have an item to cook inside. Resulted in shattering the glass tray and meting the plastic lid sitting inside which was fused to the cooking tray. Carefully wrapped up the shattered tray and melted lid in heavy paper, deposited it into the garbage, then happily placed my new E.O.M. glass cooking tray into my G.E. Profile microwave. Thank you .

We took out the broken part, it came right out,and put new part .

I read several customer reviews before starting the repair. Removed the old drive motor to make sure I was ordering the correct part. Removal consisted of removing the screws on the bottom plate, disconnecting the electrical plug from the motor, and removing the one screw that attached the motor to the housing. Installation of the new motor was the reverse.

took 6 screws out of the oven bottom
removed 2 screws that held the motor
diconnected the power plug.

plugged in power to new motor, replaced 2 screws that held it in place, replaced 6 screws that held bottom of oven

That was it...

I removed the microwave oven from the wall by unscrewing a trim plate or frame that surrounds the face of the oven. Pulled the oven out of the cabinet. Removed the glass cooking tray and rollers from the oven interior. Turned the oven on its side to expose the bottom. I unscrewed the small cover plate in the middle of the bottom which exposed the turn table motor. The motor was attached by two screws and a connector plug. In a couple minutes I removed the motor and replaced it with the new one and reassembled the oven. I put it back in the cabinet and it works like new again.