JVM1443WK02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jim from Albuquerque, NM
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Power worked but would not cook
Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Spanaway, WA
- Parts Used:
- WB15X10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broke
Followed instructions listed here that I needed to separate the inside facing on the door with a butter knife so that I could see the two screws that held the handle in place. Easy off, easy on. And I am NOT a very good handy man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Woodstock, GA
- Parts Used:
- WB55X10533
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Had a fire on stove and door of oven was melted
We removed the top vent panel and the door lifted right off. The hardest part was figuring out how to get the handle off the door. The web has easy to follow instructions so we got the inner plastic seal removed and all the screws were exposed for the handle. Once the handle was off, we pryed the melted part out of the door frame and replaced it, after cleaning the glass on both sides. Once replaced, the oven looked new again. We spent $60 for the part, rather than $450 for a new oven!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LAKE ELSINORE, CA
- Parts Used:
- WB27X10597
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Microwave wasn't heating up foods
Per instructions on part select.com website. But needs further repair because still doesn't heat food and pad is partially disabled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Destin, FL
- Parts Used:
- WB36X10071, WB36X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken glass and bad bulb
Removed one screw, slid frame out and removed broken glass. replaced bulb. The hard part was slidding the frame back in place and starting the screw. We were very surprised at the fast delivery of the parts, thank you. The sad part, a few days later the glass broke again. We are trying to get to the people at GE to solve our problem. We feel like that will not happen, we just do not have the time to stay on hold on the phone waiting for someone to solve our problem. Will reorder glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerene from Houston, TX
- Parts Used:
- WB36X10216
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass was broken
I took the cover off, and replaced the glass-- the difficult part, was ordering the glass..on the list of parts to order-- the description of the glass was mis-leading
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- selwyn from inglewood, CA
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass Carousel Cooking Tray Broke
I replaced old tray with new. Received replacement part in two days. I was surprised at the quick response time. The part ordered was right the first time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Hanover Park, IL
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave appeared to work. Fan worked, timer worked plate rotated. It just didn't heat the food!
I purchased the fuse and 3 door switches from PartSelect. Replaced the fuse first but that did not solve the problem. Then I replaced the 3 door switches and problem solved!! So fuse only cost $5.00 so glad I have a new fuse in there as well. To see how to replace door switches see videos on utube!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enid from Double Springs, AL
- Parts Used:
- WB06X10139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Roller guide for microwave turntable broke and could not be used.
Simply ordered a replacement part that was quickly and coveniently mailed to my home.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Austin, TX
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inside Bulb went out.
Remove top air grate via 2-screws. Remove metal top panel behind grate that's above bulb via 1-screw. Bulb is exposed and can be un-screwed. DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fitz Edward from SARASOTA, FL
- Parts Used:
- WB56X10270
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken door handle
Decided to replace entire door assembly since there was a small break in the door cover as well as the handle. To remove old door: take out the two screws that hold the vent cover above the door. Open the door and lift up to release from hinge pegs. Reverse process to install new door. Very Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHIL from HICKSVILLE, NY
- Parts Used:
- WB15X10023
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement of Door Handle
Gently remove the interior trim with a putty knife. Remove the two screws holding the old handle in place. Replace the new door handle. Screw the new handle in place. Align the trim and snap it back in place. Confirm the door handle is secure. I applied a little Gorilla Glue to the new handle for added strength before screwing it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Streamwood, IL
- Parts Used:
- WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Left light socket was damaged beyond repair
Handed the part to my son. He unscrewed 5 screws in the base of the microwave, it dropped down. The light mechanism was clearly in view. With the exception of some corrosion on the old piece, it was simple to remove and replace, put back together, screw back up and all worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from CICERO, IL
- Parts Used:
- WB08X10016
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bulb broke in socket, socket had deteriorated beyond repair.
Phillips screws on bottom panel allowed me to install new socket and put electric connection back. Secured bottom panel and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from Sacramento, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Glass turntable drive motor failure
Removed bottom cover of microwave, involved removing 7 screws, removed turntable motor, involved disconnecting wire harness plug, and 2 screws, connnected wiring to new motor and reinstalled with original hardware
Was this instruction helpful to you?
Thank you for voting!