JVM1640CJ03 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edwin from New York, NY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat
Replace the fuses
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Sioux Falls, SD
- Parts Used:
- WB06X10564
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken turntable coupler
Remove and installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Pensacola, FL
- Parts Used:
- WB49X10176
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
turntable broke
No repair involved, just replaced......looked online and ordered, thought it would take 4-5 days, came in perfect condition within TWO 2 days. awesomeness
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Fairview, TX
- Parts Used:
- WB02X35607
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dirty charcoal filter
Open vent, removed old filter, inserted new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kernersville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Chandler, AZ
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
When trying to run, intermittently, the light would come on but the tray wouldn't rotate or cook. When the door was open, the tray would intermittently rotate.
I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Langhorne, PA
- Parts Used:
- WB55X10816
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
GE Spacemaker microwave frame cracked
01. Remove vent cover above door and lift door out of the two hinge pin holes.
02. Lay door face down on towel and insert putty knife between choke cover and frame. Pry gently inward (towards center of door), working all the way around choke cover until it pops out.
03. Remove screws securing door handle to frame and remove door handle.
04. Disconnect main door assembly from frame by gently prying (outward, using putty knife if needed) all clips securing main door assembly to frame.
05. Remove outer glass from frame.
06. Analyze new frame for excess plastic trim (leftover from molding process), especially under and around all slots that will hold outer glass, and remove excess trim with utility knife.
07. Slide outer glass under slots at the top of the frame first. Push glass under slots as far as you can by hand.
08. This is the most difficult step: gently pry (outward, using your fingers) the tabs on the slots at the bottom of the frame until glass slips under these slots. Take your time and work back and forth, slot by slot.
09. Slide glass (using your fingers) under the slots on the right side of the frame. There are also two smaller slots on the left side of the frame (one at the top and one at the bottom). Make sure glass is seated under these slots as well.
10. Turn frame over and check that outer glass is seated against frame (no significant gaps between glass and frame) all the way around.
11. Insert main door assembly into frame and push down (using your fingers) all the way around main door assembly until all clips have engaged, securing main door assembly to frame.
12. Insert door handle into frame and secure door handle with screws.
13. Insert choke cover into frame and push down (using your fingers) all the way around until choke cover is secured in frame.
14. The top of the frame may look bowed upward in the center, indicating that the outer glass may need to be better seated in the frame. To eliminate any bow at the top, place door on its bottom on a carpeted floor and have someone hold door. Place towel on door, place wood block on towel, and gently tap wood block with rubber mallet until bow was been eliminated.
15. The bottom of the frame may look bowed downward in the center, indicating that the outer glass may need to be better seated in the frame. To eliminate any bow at the bottom, place door on its top on a carpeted floor and have someone hold door. Place towel on door, place wood block on towel, and gently tap wood block with rubber mallet until bow was been eliminated.
16. Align the two hinge pins with the two hinge pin holes on the microwave and put door back on.
17. Install vent cover above door.
18. Microwave some popcorn, grab your beverage of choice, and bask in the savings and satisfaction of doing it yourself! I hope this helped.
02. Lay door face down on towel and insert putty knife between choke cover and frame. Pry gently inward (towards center of door), working all the way around choke cover until it pops out.
03. Remove screws securing door handle to frame and remove door handle.
04. Disconnect main door assembly from frame by gently prying (outward, using putty knife if needed) all clips securing main door assembly to frame.
05. Remove outer glass from frame.
06. Analyze new frame for excess plastic trim (leftover from molding process), especially under and around all slots that will hold outer glass, and remove excess trim with utility knife.
07. Slide outer glass under slots at the top of the frame first. Push glass under slots as far as you can by hand.
08. This is the most difficult step: gently pry (outward, using your fingers) the tabs on the slots at the bottom of the frame until glass slips under these slots. Take your time and work back and forth, slot by slot.
09. Slide glass (using your fingers) under the slots on the right side of the frame. There are also two smaller slots on the left side of the frame (one at the top and one at the bottom). Make sure glass is seated under these slots as well.
10. Turn frame over and check that outer glass is seated against frame (no significant gaps between glass and frame) all the way around.
11. Insert main door assembly into frame and push down (using your fingers) all the way around main door assembly until all clips have engaged, securing main door assembly to frame.
12. Insert door handle into frame and secure door handle with screws.
13. Insert choke cover into frame and push down (using your fingers) all the way around until choke cover is secured in frame.
14. The top of the frame may look bowed upward in the center, indicating that the outer glass may need to be better seated in the frame. To eliminate any bow at the top, place door on its bottom on a carpeted floor and have someone hold door. Place towel on door, place wood block on towel, and gently tap wood block with rubber mallet until bow was been eliminated.
15. The bottom of the frame may look bowed downward in the center, indicating that the outer glass may need to be better seated in the frame. To eliminate any bow at the bottom, place door on its top on a carpeted floor and have someone hold door. Place towel on door, place wood block on towel, and gently tap wood block with rubber mallet until bow was been eliminated.
16. Align the two hinge pins with the two hinge pin holes on the microwave and put door back on.
17. Install vent cover above door.
18. Microwave some popcorn, grab your beverage of choice, and bask in the savings and satisfaction of doing it yourself! I hope this helped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from New Philidelphia, OH
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave would turn on ,BUT turn table would not turn and oven would not heat.
Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Dittmer, MO
- Parts Used:
- WB06X10689, WB49X10176
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing parts
open box and installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Sarasota, FL
- Parts Used:
- WB49X10176
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The glass microwave turntable for the microwave was dropped and it brokd.
Opened the box, put the glass turntable on the center fitted over the three little bumps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucrecia from Bothell, WA
- Parts Used:
- WB49X10176
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass tray
Replaced the tray.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Socorro, NM
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Quit working
Just like the directions said. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Chelsea, AL
- Parts Used:
- WB06X10359
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our Microwave was missing the grease filters
Ordering was easy and instillation even easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Minneola, FL
- Parts Used:
- WB26X10135
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
microwave turntable not working
working changed out the motor that arrived within 2days. Great Service and thank you so much.Brian Kerry
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from San Carlos, CA
- Parts Used:
- WB06X10564
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turntable not turning
The hard part I thought, was to find the part I needed. Not so with Part Select. It took less than a minute to find and order. The new part showed up in a few days. I noticed the new part was a little differant in a good way. The socket porition was a little deeper making it a little better. The microwave works great now.
Was this instruction helpful to you?
Thank you for voting!