JVM1660BB008 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nat Branch from Greenwell Springs, LA
- Parts Used:
- WB15X10022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broke
Removed screws and old parts. Fitted new part to door and put screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Mableton, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
noise eminating from carousel
I removed 4 screw from the under carriage of the microwave then, removed the 2 screws from the motor, replaced the motor and replaced the screws. It was so easy it took only 4 minutes to perform, better than replacing the whole unit (microwave) and less expensive too. i only wish it was made in the US, I wouldn't mind to spend a little more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Columbus, OH
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The cooking tray cracked.
First I replaced the cracked cooking tray and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Helena, MT
- Parts Used:
- WB06X10420
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Microwave turntable wouldn't turn.
Removed broken coupler hub and pushed new hub on shaft. Make sure to align the new hub correctly when pushing on to shaft. Repair took less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Big Rock, IL
- Parts Used:
- WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb fused to jolder
removed electrical wires, unscrewed holder, inserted holder, attached wires, added bulb, and put cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Kirkwood, MO
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb burned out and assembly broke when trying to replace bulb
I used the internet and your directions to complete the repair. It was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Florence from Lake Forest, IL
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tray cracked after only 4 months of use
Replacement tray was installed. It was larger than the original tray, but it fits in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from IRVINE, CA
- Parts Used:
- WB39X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dropped and broke the cooking tray
New one arrived very quickly.
Right part. Right on time. Fit like it should.
Excellent service.
Right part. Right on time. Fit like it should.
Excellent service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DIANE from SAN DIEGO, CA
- Parts Used:
- WB07X10530
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The grille on my microwave was broken
It couldn't have been easier...two screws out, two screws in. Thanks to PartSelect the grille was available and they delivered it quickly. This saved me hundreds of dollars to buy and have a new built-in microwave installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from Clearwater, FL
- Parts Used:
- WB01X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lost screws for the covers on the lights over the cook-top
Placed the screws in the proper areas, used the screw driver to tighten down and I was in business with light to spare. I am happy to have found the proper screws.
Thank you.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Webster, NY
- Parts Used:
- WB15X10022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Handle broke due to kids not using correctly.
First I figured out how to take the door apart to remove two hidden screws, once that was done it was easy to install the new part. The part came extremely fast and worked well. The picture with each part labeled helped too!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Lake Como, NJ
- Parts Used:
- WB15X10022
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door handle was broken and partially disconnected from microwave unit
You'll need to use the knife to remove the plastic frame backing from the the microwave door. Be careful when disengaging the tabs so as not to break them.Then you'll need to use a phillips screwdriver to remove the four screws from the door. Remove the damaged handle. Installation is the reverse of the removal process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from PONCA CITY, OK
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MULLINS, SC
- Parts Used:
- WB15X10022
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Door handle on microwave door groken.
I went to a U-tube video and secured the installation instructions. Video said it would take 15 minutes to do repair. Took me longer to get the door apart but finally got it installed. Had to disassemble a couple of times before getting it right but it worked out. Took a little over an hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DILLIP from LITTLETON, MA
- Parts Used:
- WB05X10007
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Broken GE microwave door latch (Part number WB05X10007)
Took out the door to be able to replace the door latch. After removing the plastic cover it was challenging to remove the broken latch (unlike other models this has two separate latches individually controlled by spring. The pin holding the latch was impossible to take out and I figured I need to take out inner layer of the door frame (metal part) to remove it. But the frame was stuck and did not come out. I found no reference how to do it on internet and then with another pair of hand pulled outwards while simultaneously pulling upward. Was finally about to pull just enough and replace the latch and push the metal frame to fit back.
Was this instruction helpful to you?
Thank you for voting!