All Installation Instructions for General Electric Microwave JVM3670SF001

Customer:: regan from oxford, MS
Parts Used:: WB49X10063
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

broken glass turntable

I placed the glasstop on the sprocket

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Barbarba from Tamaqua, PA
Parts Used:: WB26X10038
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Turntable would not turn

took screws out of bottom of microwave.dropped down bottom cover to get at drive motor I took out one screw droped down cooking tray motor disconnnected 2 wires reconnected put back up and put 1 screw in ,fastened bottom and was fixed very easy ,and parts select is the best place to find what you are looking for if I ever need parts this is where I will order from service is great and only took about 2 days to receive my part .I went to store where I bought my microwave and they wanted to sell me a new one.saved over $200

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Jerry from Sneads Ferry, NC
Parts Used:: WB26X10038
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

the plate quit rotating inside oven

removed the srews under the unit unplugged the rotor motor and unscrewed 2 screws holding in the motor. When new motor arrived I plugged it up and put it on with the 2 screws and then put the bottom filter screen piece back on with the 6 little screws. REal, real easy.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Christopher from Villa Rica, GA
Parts Used:: WB26X10038
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

turntable wouldnt turn

easy repair. removed seven screws on the underside of the microwave and lowered the bottom cover. removed two screws from the old motor, unpluged the wires. reversed this sequence to install. took less than 5 minutes.
I had previously read these steps others had posted on partselect so the job was a breeze!

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: William from Molino, AL
Parts Used:: WB26X10038
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Glass turntable stopped turning

Removed five phillips head screws. Dropped metal cover of microwave. The cover is on hinges and will stay up on its own. Removed two screws holding old motor. Replaced with new motor and replaced bottom cover of microwave. Extemely easy repair.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Portofino Island Resort from Pensacola Beach, FL
Parts Used:: WB26X10038
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

turntable was loud and not turning

I removed the screws for the bottom plate, removed the motor and installed new motor. VERY EASY. I do love that you show pictures for your parts, will definately recommend your site. Thanks for all of your help.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Joan from Hampstead, NC
Parts Used:: WB26X10038
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Turn table not turning

Removed the 5 screws that held the housing so it dropped down. removed the 2 screws to the motor. Disconnedted the plug. reinstalled the new motor. connected the plug and raised the housing and replaced the 5 screws. Took less than 10 minutes start to finish. Piece-of-cake.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Cory from Galesburg, IL
Parts Used:: WB26X10038
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Turntable / cooking tray not rotating

Let me keep this short and simple.

Disconnect the power to the microwave
Remove the (7) screws from the bottom panel
Disconnect the wires from the old Drive Motor
Remove the retaining screws of the drive motor
Then install the new drive motor in the reverse order

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Georgina from WAYNE, NJ
Parts Used:: WB06X10001
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

replace plastic ring in microwave

placed plastic ring under glass rotating plate in microwave

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: John from North Port, FL
Parts Used:: WB26X10038
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Tray motor stopped working

Removed the cover, 6 screws and then the motor, 2 screws. Unpluged the old motor and just reversed the process.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Tom from Placentia, CA
Parts Used:: WB26X10038
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Noisy turntable. (grinding)

Nice. Half dozen screws drops the bottom, 2 screws on the motor, pop in the new, reassemble and throw in the popcorn. (Was skeptical. Have replaced quite a few of these little motors in data centers. Common part in high-speed printers. Never saw one fail like this but your feedback convinced me otherwise.)

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Cecil from Gilbert, AZ
Parts Used:: WB26X10038
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Microwave cooking tray stopped turning

Unplugged microwave from the wall. Removed the screws on the bottom of the oven. Detached the light, removed the bottom panel. Unscrewed one more screw on the turn table motor and twisted to remove. Plugged in the new one and reattached the Electrical wires and bottom panel. Piece of cake. Just don't forget to reconnect the lights!

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Lanier from Adairsville, GA
Parts Used:: WB26X10038
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

tray turned slow or stopped

Remove the 8 screws in the bottom pan covering the bottom, unpluged the lights and motor plug-ins, slid or pulled the pan forward or to me and removed pan. prized the triange piece which fit into the glass tray to turn it to remove it. removed the two screws which held the motor in place. presto, got the model # off the inside panel and ordered the part on the compiiter, \. arrived in 5 days.
P.S. cleaned everything while I had it apart, toke longer than chancing the part.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: william from las vegas, NV
Parts Used:: WB26X10038
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

rotary dish tray would not revolve

Dropped the bottom of the microwave,removed the two screws holding the motor in, disconnected the electric wires, reversed the procedure and it worked like new!

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Mike from Youngsville, NC
Parts Used:: WB26X10038
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Noisy Glass Cooking tray

The Glass cooking tray was very noisy. This was verified by turning off the tray rotation.

1. Removed the two metal filters.
2. Removed the screws holding the bottom cover of the microwave. 6 or 7 I believe.
3. Removed the two screws holding the drive motor in place.
4. Started the microwave with the motor hanging down to to verify it was defective. I could hear the motor rotating and making noise.
5. Replaced the motor, bottom cover, & filters in reverse order.
6. Tested, Works fine!

1 person found this instruction helpful.

Was this instruction helpful to you?

JVM3670SF001 General Electric Microwave - Instructions