JVM1842CF02 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brent from Sacramento, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Glass turntable drive motor failure
Removed bottom cover of microwave, involved removing 7 screws, removed turntable motor, involved disconnecting wire harness plug, and 2 screws, connnected wiring to new motor and reinstalled with original hardware
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Collegeville, PA
- Parts Used:
- WB06X10286
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The glass plate in the microwave stopped turning
After examination - evidently some one had put a larger dish in the microwave and it stopped the glass plate from turning and broke the holder stirrer(small plastic piece that held the glass plate so that it could turn.
When I received the right part I simply made sure that all the prior plastic was out or out of the way and placed the new part onto to the shaft - tested it a few times, made a minor alignment and it has worked fine ever since.
Thanks to your staff for finding the right piece from the description I gave.
When I received the right part I simply made sure that all the prior plastic was out or out of the way and placed the new part onto to the shaft - tested it a few times, made a minor alignment and it has worked fine ever since.
Thanks to your staff for finding the right piece from the description I gave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Richland, WA
- Parts Used:
- WB26X10038, WB06X10144
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable wouldn’t turn
I removed a few (6) screws and disengaged the motor. Removed the parts and installed in reverse order. Replaced the screws. Easy
Cleaning up the grease from cooking for years on the stovetop below took WAY longer. But the repair was simple!!
Cleaning up the grease from cooking for years on the stovetop below took WAY longer. But the repair was simple!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Mableton, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
noise eminating from carousel
I removed 4 screw from the under carriage of the microwave then, removed the 2 screws from the motor, replaced the motor and replaced the screws. It was so easy it took only 4 minutes to perform, better than replacing the whole unit (microwave) and less expensive too. i only wish it was made in the US, I wouldn't mind to spend a little more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Big Rock, IL
- Parts Used:
- WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb fused to jolder
removed electrical wires, unscrewed holder, inserted holder, attached wires, added bulb, and put cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Kirkwood, MO
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb burned out and assembly broke when trying to replace bulb
I used the internet and your directions to complete the repair. It was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marielen from newport, RI
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked Microwave Glass Plate
Odered replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from Clearwater, FL
- Parts Used:
- WB01X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lost screws for the covers on the lights over the cook-top
Placed the screws in the proper areas, used the screw driver to tighten down and I was in business with light to spare. I am happy to have found the proper screws.
Thank you.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kambiz from Mesa, AZ
- Parts Used:
- WB02X10733
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Charcoil Filter needed to be changed.
GE microwave displayed the message that Charcoil Filter needs to be changed. I disconnected the unit and removed the top two screws then removed the top panel by sliding it gently to the left. Replaced the filter. And positioned it in the same way the old filter was installed. Replaced the top panel and screws, Connected the unit back and used the Menu option to reset the Charcoil Filter warning option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from salmon, ID
- Parts Used:
- WB36X10071
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lens Was Not Sized To Fit And Was Left Extremely Sharp
Had to take to a local glass shop for sizing and to remove sharp edges. Will never order again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Herndon, VA
- Parts Used:
- WB26X10038, WB06X10144
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Turntable coupler bore became oversized.
Small sized phillips screw driver was required. Once gaining access to the new motor the part(s) replacement was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from SEASIDE, CA
- Parts Used:
- WB36X10071, WB36X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Glass lens and two light bulbs replacements
My microwave is built in above the stove which provides lighting and fans for my stove. The glass lens cover for the lighting was cracked in several places and the light bulbs had burned out. I taped the glass lens for removal so it didn't break apart due to the cracks Removed the one screw. .Both light bulbs broke away from the base sockets as I tried to unscrew them. I used electrical tape wrapping in reverse on a lightbulb (socket end) so it was sticky for a grip on the base, shoved it in the sockets and was unable to unscrew the broke off bases. So it was very successful and no repair man was needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine J from Yuma, AZ
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drive motor not working
There where five screws to remove to get the bottom off then two to release the motor from the housing pull the electrical supply cord out then reverse the process. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from PONCA CITY, OK
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from CHESTERFIELD, VA
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no lights on microwave
ordered 2 new sockets and bulbs easy replacement great service from this site
Was this instruction helpful to you?
Thank you for voting!