JES1451WJ01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from DENVER, CO
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Microwave not turning on. All other functions operate
DISCONNECT THE POWER CORD and discharge the capacitor
Leave unplugged overnight
Remove vent grille by removing the 2 philips screws
Remove the LED panel by removing 1 phillips screw
Disconnect all connectors that plug into back of the LED board completely
Remove the wires from the switches (3) at the inside edge of the microwave door
Gently remove each switch housing and test all three switches for continuity
Carefully replace non-functioning switches and reassemble the panel
GOOD LUCK
Leave unplugged overnight
Remove vent grille by removing the 2 philips screws
Remove the LED panel by removing 1 phillips screw
Disconnect all connectors that plug into back of the LED board completely
Remove the wires from the switches (3) at the inside edge of the microwave door
Gently remove each switch housing and test all three switches for continuity
Carefully replace non-functioning switches and reassemble the panel
GOOD LUCK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from ROSELLE, IL
- Parts Used:
- WB06X10549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The drive shaft of the motor was broken and had to replace drive motor and roller guid
Cut the wire connection of access door on the bottom of the oven. Once access door was removed, I took the screw holding the drive motor in place, removed the wire connector and taped the connection to oven so that it did not drop into the bottom of the oven pulled motor out. Put new motor in, put connector back on motor secured the motor with the scre, put access door back in place put roller guide on the drive motor from inside of the oven and put plate on roller and turned it on for a test. it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kip from POWELL, OH
- Parts Used:
- WB27X10928
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Not heat
-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from JACKSON, TN
- Parts Used:
- WB36X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The Light Bulb went out
I used a phillips screw driver and a special type bit to undo the screws from the cabinet and found the light bulb and took the old one out and put the new one in and put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gilbert from TOMS RIVER, NJ
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Switch went bad, Internal Fan would run every time you open the door
Unscrewed the control panel (2 screws), lift up and let hang, with a plan screwdriver open bracket holding the switch, unplug 2 wires, replace with new switch, plug in the 2 wires, push switch back into bracket. Then slide on the control panel, put the 2 screws back. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from BLUFFTON, SC
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
The unit would run when the door was open!
First I had to accept the fact that the unit was designed to keep non-professional people from doing any repairs. The switch was installed in such a manner that I had to break the mounting to remove the switch, then drill a hole in the mounting to secure the new switch in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from POWELL, OH
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Microwave would not heat up
Part just snapped into place and wires were reattached.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dewey from MADISON, AL
- Parts Used:
- WB26X32629
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burned out magnetron
Removed cover
Disconnected capacitor from old magnetron
Removed old magnetron
Installed new part
Connected capacitor
Reinstalled cover
Disconnected capacitor from old magnetron
Removed old magnetron
Installed new part
Connected capacitor
Reinstalled cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from BOZEMAN, MT
- Parts Used:
- WB36X10063
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
light bulb burned out
Remove the top of the microwave, regular phillips screws on sides, torque screws on back. Lift up back and slide off cover. Light bulb socket is easily detached and bulb unplugged and replaced. Slide cover from back lifted slightly so lip will slide into front of microwave, than replace screws. Be sure to unplug microwave before you start.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from FULSHEAR, TX
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
M/W would not start. control panel OK
unplugged power
removed main black cover.
located part WB24X10047 and replaced
removed main black cover.
located part WB24X10047 and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- johnny from port orange, FL
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
no power in microwave in turn table wouldn't turn light would work act like door was open
remov cover to check voltage and found problem at the interlock switch ohm the switch and found it was open replace both switches it work fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bart from new sarpy, LA
- Parts Used:
- WB27X11033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Try to heat food and fuse would blow.
Went on Youtube and pulled up how to fix a microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Irwin, PA
- Parts Used:
- WB49X10139, WB06X10549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass dish would not rotate.
AFter I put the roller guide and glass cooking tray inside the microwave it still didn't spin. After check with the video, I was warned not to try to replace the motor which spins the tray, that there was a chance of electrical shock. I took the oven to my repair place and they made the repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mack from Jacksonville, FL
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
No heat.
Replaced the fuse. Result; did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Pentwater, MI
- Parts Used:
- WB06X10549
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
wheel was not turning rotisserie table
First I took out the screws holding the sides and back to the microwave. I discovered that the rotissereie motor was also damaged, but had an old GE microwave that had quit working-took out motor from other GE(motor was the same), installed motor in microwave, lined up pin to roller assy. and that was it!
Was this instruction helpful to you?
Thank you for voting!