JVM3670CF03 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave will not start
Removed three screws from the top front cover and slide it out and following I removed the touch panel and the housing that holds the switches and replaced the bad one.
Was this instruction helpful to you?
Thank you for voting!
Still runs even the door was open
Pulled it from the wall remove the front vent covers removed the control panel remove the door switches by a special screw driver bit which looks a star remove the electrical terminals pressed the plastic clip pulled the switch replaced it with new one then followed initial steps backward
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from McDonough, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The microwave was making a lot of noise and the glass plate was turning very slowly.
I diagnosed the problem myself. I googled GE parts and was refered to you guys. I ordered the part and it took less than a 5 days to arrive. I used a phillips scewdrive to remove the cover of my microwave and removed the turning glass motor. This took less that 30min and cost less that $50.00. I figured that it would have cost me approx $125.00 to get a tech person to my home for this repair.
Thanks a lot!
Bernard
Thanks a lot!
Bernard
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Muncie, IN
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave Quit working but lights worked
llation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Savannah, TX
- Parts Used:
- WB06X10144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turntable coupler broke
I took the part out of the box and handed it to my wife and said "here ya go hun, go put this under the glass turntable in the microwave. You'll know it's installed when you hear it click down" She yelled back, "easy as pie" - - - Humm.. I can't make a pie. Fortunately the old one was in one piece as the side just split so it slid off very easy. The new one just snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Sedalia, MO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy cooking tray motor with electrical smoke smell
Just removed the screws from botton of unit, unplugged and removed the burned up motor, reveresed the process to install new motor. Less than 10 minute job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from richmond, IN
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
tray drive motor
unsrewed the bottom of the microwave(there was about five or six screws)located the motor unpluged it and unscrewed the two screws holding the motor once installed i reversed the proceedure and put everything back together...simple as 1,2,3...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from North Port, FL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Tray motor stopped working
Removed the cover, 6 screws and then the motor, 2 screws. Unpluged the old motor and just reversed the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MABEL from GILROY, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable would not turn
took off steel plate---removed two screws--unpluged drive motor--replaced with new drive motor. reversed removal procedure . Took about 10 minutes.
Great service from PARTSELECT.
Great service from PARTSELECT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARBARA from PORTSMOUTH, NH
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn Table Stopped Working
Very easy repair I did not even have to take the microwave down. Just removed the 7 screws, the bottom swung down removed the 2 screws holding the motor, unplugged it put the new one in put the screws back and Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Blakely, PA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My turntable stopped working
I read several customer reviews before starting the repair. Removed the old drive motor to make sure I was ordering the correct part. Removal consisted of removing the screws on the bottom plate, disconnecting the electrical plug from the motor, and removing the one screw that attached the motor to the housing. Installation of the new motor was the reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Georgina from WAYNE, NJ
- Parts Used:
- WB06X10001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace plastic ring in microwave
placed plastic ring under glass rotating plate in microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Youngsville, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy Glass Cooking tray
The Glass cooking tray was very noisy. This was verified by turning off the tray rotation.
1. Removed the two metal filters.
2. Removed the screws holding the bottom cover of the microwave. 6 or 7 I believe.
3. Removed the two screws holding the drive motor in place.
4. Started the microwave with the motor hanging down to to verify it was defective. I could hear the motor rotating and making noise.
5. Replaced the motor, bottom cover, & filters in reverse order.
6. Tested, Works fine!
1. Removed the two metal filters.
2. Removed the screws holding the bottom cover of the microwave. 6 or 7 I believe.
3. Removed the two screws holding the drive motor in place.
4. Started the microwave with the motor hanging down to to verify it was defective. I could hear the motor rotating and making noise.
5. Replaced the motor, bottom cover, & filters in reverse order.
6. Tested, Works fine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from franklin, WI
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
cooking tray would not rotate
ha to remove the bottom ,to get at the internal screws that held the drive motor. after disconnecting the power to the moter, i removed the two screws that held it in place. i installed thre new motor , reconnected the wire plug to motor . replaced the outer screws, and the project was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William T. from San Antonio, TX
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the cooking tray would not turn (Motor was froze up)
ordered part from partselect received in about 3-4 days removed 6 ea screws from lower panel , removed 1 ea screw holding motor in place, pulled wire receptacle loose from motor, threw old motor in trash, put new motor up into plastic tray rotating device turned motor to secure on one side and installed screw to hold motor reinstalled wire plug and panel ops ckd good about 15 minutes to do could have done it quicker but my eyes ain't what they use to be Very easy fix when you get the right part and I got it on the first order with partselect ......Thank You Very Much
Was this instruction helpful to you?
Thank you for voting!