CVM2072SM1SS General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Newbern, NC
- Parts Used:
- WB06X10436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
change microwave fan discharge from front to top
damper plate was a snap-in part. rotated fan discharge to top of microwave. installed ducting to discharge food odors outside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kernersville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from gulfport, MS
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
glass broken
replaced the glass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Socorro, NM
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Quit working
Just like the directions said. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter e from far hills, NJ
- Parts Used:
- WB06X10288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Air/Grease Filters Were Worn Out
Rec'd the parts within a day or two after ordering and simply placed them where the old ones were removed and wala my stove is back filtering. Only problem, the oven won't ignite while the broiler and stove top burners are fine. Go figure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Middletown, NJ
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up
It was a snap using the instructions given. The key is getting into the unit. I did have to use a multimeter to find the failed switch since there are two of that type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Umatilla, FL
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Unit would not come on.
removed access panal, found soft switch as discribed on your web site. removed and replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Easton, PA
- Parts Used:
- WB06X10288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace bottom grease filters
Just pull down on "O" ring tab and filter will release. Install new filter in same position. you may have to pull on "O" ring to complete fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Denver, CO
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass cover for Light Bulb was cracked..
It was great...Thank you for having the part available...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Reno, NV
- Parts Used:
- WB05X10007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch on door broke
replacement door recommended $308.00 ! said no parts available ! I looked online and found one for $ 35.00 ! then i found your site and bought it for $3.00 !!! It came very fast. We looked up schematics on your site and looked on u tube for video of how to repair it. and my sons put it together in 15 minutes thank you!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manuel from Rio Vista, CA
- Parts Used:
- WB06X10520
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Several weeks with turntable stoppingand going. Turntable motor works OKay.
R/R worn turntable coupler.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from Lutz, FL
- Parts Used:
- WB06X10516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Door film was damaged by contact with tin foil
Remove old film by peeling away from glass. Lift from corner and pull to remove. Remove backing from new film slowly as you are applying to the door a little at a time. Smooth with a plastic spatular as you apply from one side of the door to the other and you will have no wrinkles or air pockets.
Was this instruction helpful to you?
Thank you for voting!
Microwave came on when door open
Turn off main power bracker. Removed fan vent, removed control panel, disconnect leads to the three monitor switches. Replaced the secondary switch (top). Reversed procedures.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clarence from Rocky Ridge, OH
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When opening door the microwave would turn on.
Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Elm Grove, WI
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave fan would run when opening the door. Evenutally the mircowave would not run, but the electrical panel was still working
Opened the microwave oven door, unscrewed two screws which held the control panel on, then I removed two of the door switches (each had two screws), and then used the continuity tester to see which one was not operating. It turned out to be the secondary door switch, replaced it and to my amazement, the microwave worked. I have never repaired an appliance before but I didn't want to replace our over-the-stove built in microwave. It was the best day ever when it was working again! The hardest part was getting myself to try the repair.
Was this instruction helpful to you?
Thank you for voting!