JVM1850DMBB01 General Electric Microwave - Instructions

Had to pry the front top of mircowave open and bend down and force this carbon filter in on an angle .Had to call several numbers for instructions. Very awkward and ridiculous to put carbon filter in-besides, it should have come with one to start with!!

Open the box that the part came in and place it in the microwave. The best is how fast it came to my home. Thanks

I purchased the fuse and 3 door switches from PartSelect. Replaced the fuse first but that did not solve the problem. Then I replaced the 3 door switches and problem solved!! So fuse only cost $5.00 so glad I have a new fuse in there as well. To see how to replace door switches see videos on utube!!

Removed one screw, slid frame out and removed broken glass. replaced bulb. The hard part was slidding the frame back in place and starting the screw. We were very surprised at the fast delivery of the parts, thank you. The sad part, a few days later the glass broke again. We are trying to get to the people at GE to solve our problem. We feel like that will not happen, we just do not have the time to stay on hold on the phone waiting for someone to solve our problem. Will reorder glass.

The new turntable shipment was super fast!!! I received it only a few days after ordering it. Installation was nothing more than placing it in the microwave oven.

GREAT Transaction!!! Thanjs!!!

Followed instructions on You Tube. I had an over the stove model. First I unplugged the electric cord,removed screws from bottom of microwave, removed the 1screw on motor,disconnected the electric wires which just pop off as a unit and replaced the motor and put bottom back on. Easy instructions on You Tube

just set the glass turntable in and bingo it worked
no tools needed. thanks for such a fast delivery
sincerly dennis and chris delbello

Remove top air grate via 2-screws. Remove metal top panel behind grate that's above bulb via 1-screw. Bulb is exposed and can be un-screwed. DONE

Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!

Disconnected power cord from receptacle. Removed 5 screws in bottom panel and allowed it to swing downward on rear hinged edge. Disconnnected power wires to motor. Removed screw to detach motor. Inserted coupler through hole beneath center of turntable. Inserted motor shaft into coupler and re-attached motor. Connected power wires to motor and then closed the bottom panel and re-inserted the 5 screws.

Handed the part to my son. He unscrewed 5 screws in the base of the microwave, it dropped down. The light mechanism was clearly in view. With the exception of some corrosion on the old piece, it was simple to remove and replace, put back together, screw back up and all worked fine.

Phillips screws on bottom panel allowed me to install new socket and put electric connection back. Secured bottom panel and that was it.

Removed bottom cover of microwave, involved removing 7 screws, removed turntable motor, involved disconnecting wire harness plug, and 2 screws, connnected wiring to new motor and reinstalled with original hardware

Removed the outer cover to access the door switches. Turns out there were three switches, but I determined that only two were bad. When the small colored tab on the switch is pushed in it should make a clicking sound. The two bad switches had no resistance and did not make any noise when pressed. Removing the switch is relatively easy, you simply pull it away from a couple small tabs holding them in place. After reconnecting the wire leads, insert back into the holding tabs and install the cover.

After examination - evidently some one had put a larger dish in the microwave and it stopped the glass plate from turning and broke the holder stirrer(small plastic piece that held the glass plate so that it could turn.
When I received the right part I simply made sure that all the prior plastic was out or out of the way and placed the new part onto to the shaft - tested it a few times, made a minor alignment and it has worked fine ever since.
Thanks to your staff for finding the right piece from the description I gave.