JEB1095CB03 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Debra from Concord, CA
- Parts Used:
- WB27X10597
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Not heating
Removed the above stove microhood. Removed the side panels & the top panel. Diode located on right hand side of microwave. Removed with screwdriver & replaced new diode. It's best to get the microwave schematic online to pinpoint location of the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SUGAR HILL, GA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burn ed out bulbs
I removed light bulb cover shield,took out defective bulbs and replaced with new ones. 5minute repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MANUEL from ESCONDIDO, CA
- Parts Used:
- WB27X10597
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
diode burnt
it was a simple screw in on both ends. no soldering
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Arlington, TX
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light bulb in the over-stove microwave
Removed the one phillips screw that holds the light lens in place, drop the lens down for access to the burned out bulb, screw in the new bulb, replace the lens.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Walnut Creek, CA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light bulb below the over burned out
Getting the old bulb out of the socket was not an easy job as the factory seals the base of the bulb to the socket and for what reason I do not know. The seal has to be broken away to remove the bulb. I broke the seal with a knife and then proceeded to unscrew the bulb. The bulb at that point shattered in my hand and I was left with just the base of the bulb stuck in the socket. it took much effort to be able to work loose the base with a needle nose pliers and much sweat. The installation however went very smooth and Part Select did a fine job of sending me the right part in a very short period of time. They are a great source for any appliance part needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from schererville, IN
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad bulb
unscrewed cover, took old bulb out, screwed new bulb in.relaced cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Middletown, NJ
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up
It was a snap using the instructions given. The key is getting into the unit. I did have to use a multimeter to find the failed switch since there are two of that type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from RIVERSIDE, IA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lights under microwave (that we use as a kitchen night light went out.
undid plate exposing bulbs. Bulbs were blown to the extent that I could not see the size or wattage. Went to website, got the data ... including how to find the model and serial number plate, entered the info, looked at the exploded drawing, ordered 2 new bulbs and 3 days later they showed up at our door FedEX.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from Albertville, AL
- Parts Used:
- WB36X10003, WB24X830
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
fan came on when door was opened.
First, there are three door operated switches in this model. The monitor sw, the secondary sw (both of these are on the bottom in the same bracket) and the door sensing sw on top. The door sensing and secondary switches are both N.O. and have the same part number (probably why you show just two switches). The monitor sw is N.C. and it was not my problem. The secondary sw was bad on my oven but I had replaced the door sensing sw (which wasn't bad) on a previous order and kept the old one so I used it to make the repair. All three switches can be accessed without removing the oven by removing the discharge louver (remove two flat head screws on top and slide the louver to the left) then carefully remove the control panel (one screw on top and lift out). The switches are held in place by a plastic tongue that fits into the rear mounting hole on the switch. I used a common screw driver with a small tip to gently lift the tongue and slide the switch out with needle nose pliers. The new switch just snaps back in. The switch holder bracket looks like it would be easily broken so be gentle. I don't know what the symptoms would be if either of the other switches were bad so I would recommend buying all three and you would have them if one of the others failed in the future. The information I gave on the switches came from a schematic I found inside the control box. Hope this is helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marla from Arlington, TX
- Parts Used:
- WB24X829
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fan stayed running when door was open...all else working fine
First, unplug microwave. Unscrew two screws at top of microwave, slide grill cover left and remove. This allows access to single screw holding control panel. Remove this screw and lift up control panel to remove. Secondary door switch is black switch at lowest position. The switch is held in place by a lever in back and very hard to get to. Remove the wires plugged into the switch, then remove two screws holding the plastic switch mount that holds all three switches. These screws use a "star" type screwdriver. Once the plastic mount is free, lift it up, right, and tip it slightly to find the lever that will release the black secondary door switch (the lowest switch)...release the broken switch, snap the new switch in its place. Replace the plastic mount by lifting and replacing back into position and replace the two "star" screws. Now, replace the wires onto the new switch, and test operation. Replace control panel, and top grill. It goes faster than it writes...getting the old switch out through that difficult to reach lever was the hardest part...still less than thirty minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Gaithersburg, MD
- Parts Used:
- WB27X10597
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven failed to heat food.
Remove the microwave cover. Requires a phillips screwdriver and a torx security bit/nut driver (there are two security type screws on the back...guess they don't want you to do this at home!). I had to buy the a security bit set (about $7). The diode is easily accessible on the right side under the fan. Requires removing on small phillips screw and unplugging on electrical connection. GE provides some instructions in an envelope on top (after cover removed). There is a warning/instruction to discharge the capacitor before service. This was not a problem for me. Actual diode replacement took 30 seconds. Whole job = 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
Microwave came on when door open
Turn off main power bracker. Removed fan vent, removed control panel, disconnect leads to the three monitor switches. Replaced the secondary switch (top). Reversed procedures.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Elm Grove, WI
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave fan would run when opening the door. Evenutally the mircowave would not run, but the electrical panel was still working
Opened the microwave oven door, unscrewed two screws which held the control panel on, then I removed two of the door switches (each had two screws), and then used the continuity tester to see which one was not operating. It turned out to be the secondary door switch, replaced it and to my amazement, the microwave worked. I have never repaired an appliance before but I didn't want to replace our over-the-stove built in microwave. It was the best day ever when it was working again! The hardest part was getting myself to try the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clarence from Rocky Ridge, OH
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When opening door the microwave would turn on.
Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.
Was this instruction helpful to you?
Thank you for voting!